PFSTAT(8)

NAME
pfstat - collect packet filter statistics and generate graphs

SYNOPSIS
pfstat [-c config] [-d database] [-r host[:port]] [-q] [-p] [-t -days[:days]]

DESCRIPTION
The pfstat utility can query statistics from the packet filter device pf(4) and produce graphs from the collected data.

The options are as follows:

-q  Query the current set of statistics from the packet filter and store it in the database. This is usually done from a crontab(5) like this:

        * * * * * /usr/local/bin/pfstat -q

-r host[:port]
    Query the statistics from a remote host running pfstatd(8). Default is to query the local packet filter through the device special file /dev/pf, not requiring any running pfstatd(8).

-p  Produce the configured set of graph images based on the statistics collected beforehand.

-t days:[days]
    Truncate the database, removing entries older than the specified number of days. The first value applies to uncompressed entries which constitute roughly 90 percent of the database, the second value to compressed entries. Uncompressed entries are needed only for high-resolution graphs over short time periods.

    Assuming statistics are queried every I seconds, and a graph of width W pixels covering a time period of T seconds is generated, then uncompressed entries are only used when T/I < W*10.

    In other words, removing uncompressed entries earlier than compressed ones drastically reduces the database size. Graphs can be generated over the entire time range the compressed entries cover (monthly or yearly graphs), and high resolution graphs over short time periods in the recent past don't lose any precision. The precision is gradually lost for older periods.

    A typical invokation would be

        pfstat -t 31:365

    This removes uncompressed entries older than a month and compressed entries older than a year, allowing generation of graphs up to one year into the past, while keeping full precision for one month.

-c config
    Use the specified configuration file instead of the default /etc/pfstat.conf. Syntax:

        collect = "collect" number = coldef .
        coldef  = ( global | iface | queue ) [ "diff" ] .
        global  = "global" ( states | counter ) .
        states  = "states" ( "entries" | "inserts" | "removals" |
                             "searches" ) .
        counter = "counter" ( "match" | "bad-offset" | ... ) .
        iface   = "interface" name ( "pass" | "block" )
                              ( "bytes" | "packets" ) ( "in" | "out" )
                              ( "ipv4" | "ipv6" ) .
        queue   = "queue" name ( "pass" | "drop" | "other" )
                      ( "packets" | "bytes" | number )
        image   = "image" filename "{"
                      time type size [ left ] [ right ] "}" .
        time    = "from" number [ unit ] [ "to" number [ unit ] ] .
        unit    = "minutes" | "hours" | "days" | "weeks" | "months" |
                              "years" .
        type	= "type" ( "jpeg" | "png" ) .
        size    = "width" number "height" number .
        left    = "left" graphs .
        right   = "right" graphs .
        graphs  = graph [ "," graphs ] .
        graph   = "graph" number [ "bps" ] [ "avg" | "min" | "max" ]
                          label unit "color" red green blue [ "filled" ] .

    collect lines define what values to store in the database. Each definition should use a unique number, which is used in graph lines to reference those values.

    The diff option causes differential values (change of value per second) to be stored instead of absolute values. For example, storing interface byte counters (which count the number of bytes since last reset) differentially produces values representing current speed (bytes per second).

    Several images can be defined in the same config file. An image can include two independent y-axes, both of which auto-scale independently to the maximum value in the selected range. Each axis can display an arbitrary number of graphs.

    When the bps option is used, values are multiplied by eight, and the unit prefixes 'k' (kilo), 'm' (mega), etc. are multiples of 1024, instead of 1000.

-d database
    Database file. Default is /var/db/pfstat.db.

EXAMPLES

    collect 1 = interface "sis0" pass bytes in ipv4 diff
    collect 2 = interface "sis0" pass bytes out ipv4 diff
    image "/var/www/htdocs/bandwidth.jpg" {
            from 7 days to now
            width 1000 height 400
            left
                    graph 1 bps "in" "bits/s" color 0 192 0 filled
            right
                    graph 2 bps "out" "bits/s" color 0 0 255
    }
    collect 3 = global states entries
    image "/var/www/htdocs/states.jpg" {
    	from 12 months to now
    	width 800 height 200
    	left
    		graph 3 "states" "entries" color 200 0 0
    }

SEE ALSO
pf(4), crontab(5), pfctl(8), pfstatd(8)