Distribution:   OpenBSD
Maintainer:     Devin Reade <gdr@gno.org>

$Id: README,v 1.2 2004-08-26 09:20:07 kerns Exp $

=======================================================
MAKE SURE YOU READ THE "IMPORTANT NOTE" SECTION, BELOW!
=======================================================

Your DEVICE should normally be set to /dev/cua00 for the first
serial port.

Overview
--------

The OpenBSD distribution of apcupsd operates a bit differently from
the other distributions; the shutdown sequence (once the UPS can 
no longer sustain the dependent servers) has been modified.

For most operating systems, the following sequence occurs:
        1. mains power loss
        2. warning messages are sent from the master at various intervals
        3. minimum battery level or max run time is reached
        4. apcupsd invokes the control script with 'doshutdown' argument,
           then exits
        5. the control script initiates a system shutdown
        6. as part of the system shutdown sequence, apcupsd is called in
           a "one shot" mode in order to send a message to the UPS telling
           it to kill the power in a configurable number of seconds
        7. the system finishes its halt sequence
        8. the UPS kills power to the system until mains power returns

During the OpenBSD shutdown sequence, however, the second "one shot" call
to apcupsd will fail because after the shutdown sequence has started, the
serial port cannot be reopened.  Therefore, the OpenBSD sequence has been
modified to the following:

        1. mains power loss
        2. warning messages are sent from the master at various intervals
        3. minimum battery level or max run time is reached
        4. apcupsd sends message to UPS to power off after a configurable
           number of seconds
        5. apcupsd invokes the control script with 'doshutdown' argument,
           then exits
        5. the control script initiates a system shutdown
        6. the system finishes its halt sequence
        7. the UPS kills power to the system until mains power returns

    vvvvvvvvvvvvvv
--> IMPORTANT NOTE <--
    ^^^^^^^^^^^^^^

        Because of the modified shutdown sequence, the default number
        of seconds that the UPS will run after being given its "power off"
        message may not be sufficient to properly halt the system.
        Therefore, it is critical that this interval be verified and 
        probably modified.  See the section below on "Modifying the
        Power Off Interval" for details on how this is done.

As a consequence of the above, another difference is that once the
shutdown sequence has been initiated, it cannot be cancelled even if
mains power returns.  This has implications for a hetrogeneous environment:
If the OpenBSD server is running in apcupsd networked mode with another
machine such as a Linux server, it is possible for the former to complete
the shutdown and the latter to cancel it.  Depending on which machine
is the master and which is the slave, this could either result in one
machine remaining in a halted state indefinitely, or (worse) the other
machine losing power while not in a halted state.

Therefore, it is strongly recommended that when running in network
mode, that shutdown cancellation be disabled on all machines.

To date, the OpenBSD code has only been tested in standalone mode and
as a net master, with a Slackware Linux machine as the net slave.

Modifying the Power Off Interval
--------------------------------

[The information in this section is already available in the primary
 apcupsd documents -- this section merely makes things a bit more 
 explicit in the context of OpenBSD.]

Once you have run the commands

        configure
        make 
        make install

in the apcupsd source tree and verified the values (most notably, the
"DEVICE" value) in the /etc/apcupsd/apcupsd.conf file, you should be
able to manually start apcupsd by executing the following:

        /usr/local/sbin/apcupsctl start

After the daemon starts, you should be able to get your current configuration
by issuing the command:

        /usr/local/sbin/apcupsctl status

Since the daemon prints status to stderr, you may have to redirect the 
output to a file in order to view it.  It will also take a few seconds
before you can get the status.  If you either see a message about
"UPS not ready to report" or if the BCHARGE value is "000.0 Percent",
then you have to wait a few seconds a try again.

Once you have good status data, look for the value of the "DSHUTD" 
parameter.  This is the interval between the time the UPS receives a
shutdown request and the time the power is killed.  If the value is 20
(seconds), then you have to modify it.  My OpenBSD machine shuts down
fairly quickly, so I find a value of 180 seconds to be suitable.  Note
that there are only a few discrete values which are permissable.  See 
the apcupsd.conf file for details.

If you need to change this value, edit the "SLEEP" parameter in your
apcupsd.conf file and set it to the appropriate value.  That parameter
is grouped, in the configuration file, with a bunch of other parameters
used for programming the UPS EEPROM.   Make sure all the other parameters
are commented out (you only want to change one at a time).

Before you can reset the EPROM, shut down the running apcupsd:
        /usr/local/sbin/apcupsctl stop
Make sure there are no apcupsd processes left running before you continue:
        ps auxww | grep apc
Now you can modifiy the EPROM with the new configuration file:
        /sbin/apcupsd -c
That will take about 30 or 45 seconds to complete.  You should see messages
regarding which EPROM values have been changed (and what the old values
were).  Read them to ensure that you didn't change something that you 
hadn't intended to change.

You should probably ensure that the "MINUTES" parameter in your configuration
file makes sense given the value you selected for "SLEEP" -- chances are
that you want "MINUTES" to be at least as long as "SLEEP".  Remember that one
is specified in minutes, and the other in seconds.  The "MINUTES" parameter
is used whenever apcupsd starts up; you don't need to reset the EPROM when
"MINUTES" is changed.
