This is mgetty.info, produced by makeinfo version 4.8 from mgetty.texi.

INFO-DIR-SECTION Miscellaneous
START-INFO-DIR-ENTRY
* mgetty: (mgetty).               Smart getty replacement.
* sendfax: (mgetty).              Standalone backend program to send fax files.
END-INFO-DIR-ENTRY

   This is the online documentation for the mgetty + sendfax package.

   Copyright (C) 1993-2005 Gert Doering +
+START-INFO-DIR-ENTRY
+* Mgetty: (mgetty).           Mgetty: an advanced getty that can manage faxes.
+END-INFO-DIR-ENTRY
+


File: mgetty.info,  Node: Top,  Next: Intro,  Prev: (dir),  Up: (dir)

mgetty + sendfax
****************

This is the online documentation for the mgetty+sendfax package written
by Gert Doering.

* Menu:

* Intro::           Introduction
* mgetty::          Using `mgetty'
* Fax::             Fax Operations
* voice::           Voice Operations
* Problems::        Common problems and solutions (TROUBLESHOOTING)
* Thanks::          Credits


File: mgetty.info,  Node: Intro,  Next: mgetty,  Prev: Top,  Up: Top

1 Introduction
**************

`mgetty' allows you to make optimum use of your modem or fax modem in a
unix environment. `mgetty' handles incoming calls without interfering
with outgoing calls. If the modem can do fax class 2 or 2.0, `mgetty'
can also receive faxes.

   `sendfax' is a standalone backend program to send fax files.

   This manual explains how to configure and install the package on
various operating systems and modems, and how to use those programs.

* Menu:

* Copying::         Copying conditions and (lack of) warranty
* Overview::        Features of `mgetty' and `sendfax'
* Supported::       Supported systems and modems
* Install::         Configuration and installation
* intro-runtime::   Runtime Configuration: an Overview


File: mgetty.info,  Node: Copying,  Next: Overview,  Prev: Intro,  Up: Intro

1.1 Copying conditions and (lack of) warranty
=============================================

*WARNING:* This package is still BETA software. Use it at your own
risk, there is *no* warranty. If it erases all the data on your hard
disk, damages your hardware, or kills your dog, that is entirely your
problem. Anyway, the program works for me and quite a lot of other
people.

   The `mgetty+sendfax' package is Copyright (C) 1993-2002 Gert
Doering, Klaus Weidner, Marc Eberhard, Marc Schaefer, and others.

   It is distributed on terms of the GNU General Public License, which
you can find in the main mgetty directory in the file `COPYING'.

   If you want to redistribute `mgetty+sendfax' under a different
license (like in "selling it to your customers"), contact me, and we
will work something out.


File: mgetty.info,  Node: Overview,  Next: Supported,  Prev: Copying,  Up: Intro

1.2 Features of `mgetty' and `sendfax'
======================================

This package contains two major programs, `mgetty' and `sendfax'.

   This is what you can do with `sendfax' if you have a standard class
2 fax modem:

   * send faxes directly or using shell scripts

   * do "fax polling", this means you can call the weather station and
     get them to send you a fax containing the current weather map.
     (Not all modem manufacturers implement this feature in their
     modems!)

   * create a "fax queue", outgoing faxes get sent automatically, the
     user is informed by mail about the result.

   `mgetty' allows you to use your modem line for receiving fax and
data calls, without hindering dial-out on the same line.

   * `mgetty' knows about "smart" modems, and will make sure that the
     modem is always in a defined state (specific modem initialization
     possible)

   * Incoming calls are answered manually (`RING' -> `ATA' ->
     `CONNECT') instead of using auto-answer (`ATS0=1'), this way the
     modem won't pick up the phone when the machine is down or logins
     are not allowed.

   * `mgetty' incorporates all features of uugetty: it honours `LCK.*'
     files created by `uucico' and other comm programs, this way it will
     prevent dial-outs while a caller is online and it won't be
     confused if other programs use the modem.

   * `mgetty' can receive faxes (if your modem supports fax class 2 or
     2.0).

   * `mgetty' knows about incoming FidoNet calls.

   * `mgetty' has extensive logging / debugging features

   * do "fax poll sending", that is, you can setup your machine as fax
     poll server, to send some fax pages to "fax poll" callers. (Send
     informations about your system, the current wheather map, ...). Be
     warned, even less modems support this feature.

   * `mgetty' can selectively refuse calls based upon CallerID, if your
     local Telco supports it and your modem knows how to decode and
     report it.  CallerID is also logged.

   * `mgetty' has facilities to allow you to refuse incoming FAXes when
     available disk space is low.


   If you have any bug reports, suggestions, please report them to
gert@greenie.muc.de (or, if [and only if!] that doesn't work, to
gert@space.net).

   Also, I have created a mgetty mailing list, for discussion of
problems and suggestions. You can subscribe by sending a request to
mgetty-request@muc.de (forwarded to Crynwr.com for precessing) and you
can send articles to the list by sending them to mgetty@muc.de.  The
list manager will write you back for verification of your address, so
make sure it is correct.

   The mailing list is currently gated bidirectionally into the
newsgroup de.alt.comm.mgetty. In spite of being in the German language
hierarchy, the language in the group is English. Posts in German should
be ignored.

   The mailing list is archived on a WWW site, look at
`http://www.elilabs.com/mgarc/index.html' (many thanks to Robert J.
Brown, rj@eli.elilabs.com).  It's also archived by Marc Schaefer, on
`http://search.alphanet.ch/' *(NEW!)*.  The latter search engine
indexes somewhat more than only the mgetty list, so you might want to
add 'mgetty' to your query to restrict it.


File: mgetty.info,  Node: Supported,  Next: Install,  Prev: Overview,  Up: Intro

1.3 Supported systems and modems
================================

Mgetty has been successfully installed and run on the following systems
(though older systems might need work to get current mgetty versions to
compile):

         SCO Unix 3.2.1 (ODT 1.0)                   (well tested)
         SCO Unix 3.2.4 (ODT 2.0 + 3.0)             (very well tested)
         SCO Open Server 5.0                        (well tested)
         Linux (everything from 0.99pl1 up)         (very well tested)
         ISC Unix 3.0                                (tested)
         SVR4 Unix                                   (well tested)
         SVR4.2 Unix                                 (needs more testing)
         AT&T 3B1 3.51m                              (tested)
         HP-UX 8.x and 9.x                           (well tested)
         AIX 3.2.5, 4.1, 4.2 and 4.3                  (very well tested)
         SunOS 4                                     (well tested)
         Solaris 2.x                                 (well tested)
         NetBSD / FreeBSD (all versions)            (very well tested)
         Apple Darwin (Kernel 5.1)                  (tested)

   It should be possible to run mgetty on any other Unix with `termio.h'
or `termios.h'. For best results, use of the library functions
`select(S)' or `poll(S)' is recommended, but there's a workaround if
your system hasn't either. (Warning: for Unix SVR3.1 or earlier, _do
not use poll()_, it will not work on tty devices.)

   Up to now, it has been successfully used with the following modems
(no exhaustive list) in fax mode:

         ZyXEL U1496 (various ROM releases)
             (very well tested, a couple of problems remain, depending on the
              ROM release)

         ZyXEL 2864/2864I (various ROM releases)
             (very well tested, some firmware versions have problems)

         USR Courier/Sportster series
             (well tested, Couriers work great, Sportsters are ok for data)

         MultiTech (various models)
             (tested, works very well, very good fax implementation)

         SupraFAX v32bis
             (tested, works well, no fax polling available)

         GVC FM144/+
             (tested, works well, no fax polling available)

         TKR DM-24VF+ (Deltafax)
             (tested, works quite well)

         Zoom V.FAST 24K/28K
             (tested, works, some problems with fax/data distinction)

         ELSA MicroLink (various)
         	(tested, usually works well, some firmware versions have issues)

   It _should_ work with all class 2 faxmodems. Maybe the DC2 character
sent at the beginning of a page by `faxrec.c' must be changed to XON,
for very old class 2 modems (implementing very old drafts of the
standard). *Note Modems::.

   In Data mode, it will work with every Hayes-compatible modem.


File: mgetty.info,  Node: Install,  Next: intro-runtime,  Prev: Supported,  Up: Intro

1.4 Configuration and installation
==================================

Compiling of the package should be quite straightforward. You have to
copy `policy.h-dist' to `policy.h' and edit it to set some local policy
options, see the comments in that file.  (Most default values should be
fine, though).

   Then, edit the `Makefile', to specify installation paths, some
system defines and some system dependent libraries (explained there).

   After that, a `make' should build the programs and the documentation.

   Before you can run `make install' to setup and install everything,
make sure that the user that you specified for `FAX_OUT_USER' in
`Makefile' exists in your system.  This user will be needed to run
`faxrunq' or `faxrunqd', and owns all the outgoing fax queue (this has
been changed for 1.1.29 - earlier versions had the fax queue world
writeable, which was a security problem).

   If your compiler complains about the `#ident' lines I use for `RCS',
please run `make noident', that will take care of those lines (this is
only needed if the compiler refuses to go on - some compilers complain,
but go on anyways).

   If you get an error message about "unresolved symbols" when linking,
you may have to tell the package whether you have the select(S) or
poll(S) system calls, by defining `-DUSE_SELECT' or `-DUSE_POLL' flags
in the `Makefile' (If you don't know it, try both, until the error goes
away). If it's not related to `select' or `poll', please check the
systems man pages which libraries to link, and add appropriate
`-l<library>' statements to `LIBS'.

   If your system has neither the select(S) call nor the poll(S) call,
mgetty is not fully operational--these functions are the only way to
prevent mgetty from eating up characters when some other process is
trying to dial out.

   You can use mgetty anyway, by specifying `-DUSE_READ' in the
Makefile, but beware: with this, mgetty will eat up at least one
character of the modem response when another program is dialing out.
That may lead to disastrous results if e.g. the `CONNECT' string is
thus corrupted, but most of the time, the character that `mgetty' eats
away will be an `cr' or `nl' or part of the command that the modem
echoes back.

   If you have any problems compiling mgetty and sendfax (on a Unix-like
system--I do not support MS-DOS or Windows!), please contact me.  _But
make sure that you have read the documentation!_

   Later on in this document you can find some more detailed
instructions about specific operating systems (Linux, FreeBSD, and so
on).


File: mgetty.info,  Node: intro-runtime,  Prev: Install,  Up: Intro

1.5 Runtime configuration: Overview
===================================

If `mgetty' or `sendfax' are run "as is", they will use their
compiled-in defaults from `policy.h'.

   If the configuration files `mgetty.config' (*note runtime-mgetty::)
and `sendfax.config' (*note runtime-sendfax::) exist (and are
readable), both programs will get their run-time configuration from
there.  Items not specified there will still be taken from the
compiled-in defaults. Command line switches will always override those
settings. The configuration files are usually located in
`/etc/mgetty+sendfax/'.

   If you specify command line arguments (see the mgetty(1) and
sendfax(8) man pages for details), this will override both compiled-in
and config file defaults.


File: mgetty.info,  Node: mgetty,  Next: Fax,  Prev: Intro,  Up: Top

2 Using `mgetty'
****************

You can't simply call `mgetty' from a shell script (like `/etc/rc') or
interactively, because login is not possible unless mgetty is called
directly by the `init' process. The next sections explain how to do
this.

* Menu:

* How::             How `mgetty' works
* Inittab::         The `/etc/inittab' entry
* Devices::         Choosing the right device
* Logs::            Log files
* Deny::            Denying logins (and scheduling)
* Direct::          Direct serial lines
* Interaction::     Interaction between `mgetty' and other programs
* Caller-ID::       Using Caller-ID to selectively accept or reject calls
* runtime-mgetty::  Runtime configuration: `mgetty.config'


File: mgetty.info,  Node: How,  Next: Inittab,  Prev: mgetty,  Up: mgetty

2.1 How `mgetty' works
======================

To help you understand how mgetty works, here is an example of what
happens in various circumstances when you use it to control a modem
connected to a serial line, e.g. `/dev/tty2a'.

   When the computer is booted, the operating system starts the `init'
process, which is responsible for making sure that gettys are running on
the appropiate i/o devices, e.g. virtual terminals, serial lines and
modems.  `init' reads its configuration file, `/etc/inittab' (on System
V), which tells it that the line `/dev/tty2a' should be controlled by
mgetty. It then creates an entry in `/etc/utmp' (`login' needs this,
that's why you can't log in if you try to start mgetty by hand), and
forks a new `mgetty' process, using the command line specified.

   When mgetty is started, it first checks if a valid lock file held by
another process exists. If it does, this means that the port is in use,
and mgetty will wait until the lock file goes away. Invalid lock files,
e.g. for nonexistent processes ("stale" locks), are ignored.

   Once the port is free, mgetty creates its own lockfile, initializes
the modem and removes its lock file again. Then it waits for something
to happen on the port. Note that it does not _read_ any characters, it
just checks if there are any available for reading by using `poll()' or
`select()'.

   There are two possibilities once characters arrive, either a
different program (e.g.  `uucico') has started dialing out or a `RING'
was sent by the modem.  In the first case, mgetty should leave the port
alone. This is easy _if_ the program dialing out has created a valid
lock file: mgetty will find it, wait for it to go away and then exit
(which will cause `init' to start a fresh `mgetty' process, which will
then wait for the next call).

   In the second case, when there is no lock file, mgetty assumes that
the phone is ringing, creates a lock file and reads the characters
available. If it finds a `RING', it picks up the phone by sending `ATA'
and waits for the `CONNECT' message. If the caller is a fax machine, it
saves the fax in the directory `FAX_SPOOL_IN' (usually
`/var/spool/fax/incoming') and exits. If it is a modem, it prints
`/etc/issue' and displays a login prompt. Once it has received a login
string, it calls `/usr/bin/login' and lets it handle things from here.
`login' will read the password and will then start the user's login
shell, `uucico', a dialup SLIP link or whatever, but mgetty doesn't
care about that. The lock file remains so that no other programs will
try to use the modem while somebody is logged in.

   (If the `login.config' configuration file is used, mgetty can also
call other login programs than `/usr/bin/login'. See below for more
details)

   Once mgetty has terminated for whatever reason, `init' might
reinitialize the port (this is why mgetty waits for lock files to go
away instead of quitting immediately) and will then start a new
`mgetty' process, which will remove lock files left over from the last
login.

   The lock file handling is tricky, but very important. It is essential
that _all_ programs that use the modem agree on one locking protocol,
otherwise one program might not know that the modem is in use and will
try to dial out anyway. A typical lock file is a file called
`/var/spool/lock/LCK..ttyxx', containing the process ID (PID) of the
process currently using the modem. Other processes can read it and tell
if the lock file belongs to an existing process or if it is "stale" and
can be removed. This will obviously not work if the processes look for
lock files in different places, or if one of them writes its PID in
ASCII and another one tries to read it as a binary number (while mgetty
and sendfax do not care whether foreign lock files are written in
binary or ascii format, other programs do! mgetty can sometimes detect
this problem, and will then log a warning).


File: mgetty.info,  Node: Inittab,  Next: Devices,  Prev: How,  Up: mgetty

2.2 The `/etc/inittab' entry
============================

An typical `inittab' entry for `mgetty' looks like this (on
SystemV-style OSes):

     <tt>:rlevel:<respawn|off>:/usr/local/sbin/mgetty [options] <device>

   where `tt' is a short form of the `device' name, used by `init' and
`who' for internal purposes. Usually this is something like `S0' or
`2A' or so.

   `rlevel' specifies the runlevel that the command in the fourth field
is run at, this may be `23' or `56' or so, look at `man init' and the
existing `/etc/inittab' on your system.

   The next field tells `init' whether that entry is active (`respawn')
or not (`off'), and the fourth field specifies the full path of the
program to run.

   The following options are available for `mgetty':

   `-x <LEVEL>' sets the debugging level. This is very important for
diagnosing problems, as with higher levels, `mgetty' will write very
detailed informations about its internal workings to its log file.

   `-s <SPEED>' sets the port speed. If not specified, the default from
`policy.h', (definition `DEFAULT_PORTSPEED') will be used.

   `-k <SPACE>' sets the minimum number of kbytes required on the
incoming FAX spool directory.  If there isn't this much space in the
spool directory, the connection is terminated.  The default is 1
megabyte.

   `-m 'EXPECT SEND ...'' sets the modem initialization sequence.

   `-r' for direct lines (no modem chats are done)

   `-p <LOGIN PROMPT>' sets the login prompt (various escapes are
allowed)

   `-n <RINGS>' sets the number of `RING' messages to expect before
sending `ATA' to answer the phone. Default is one `RING'.

   `-R <SEC>' tells mgetty to enable "ring-back" or "ring-twice" mode.
This means that mgetty won't pick up a call immediately, but the caller
has to hang up after the first ring, and call again in the next <SEC>
seconds.

   `-i `/etc/issue'' specifies the issue file to display before
prompting for login.

   `-S `<fax_document>'' specifies the document(s) to send to polling
fax machines (full path required). `<fax_document>' has to be in G3
format (as for `sendfax'), or a text file listing G3 fax files (one
file per line).

   A sample entry in `/etc/inittab' might look like this:

     F1a:23:respawn:/usr/local/sbin/mgetty -x 3 tty2a

   For a more detailed explanation of all the options, please look into
the `mgetty(1)' man page.


File: mgetty.info,  Node: Devices,  Next: Logs,  Prev: Inittab,  Up: mgetty

2.3 Choosing the right device
=============================

Some operating systems provide two separate devices for each serial
line, one of which is intended especially for gettys. This is _NOT_ a
good idea, because it won't work with `mgetty'. It is meant for modems
used in auto-answer mode.

   `mgetty' picks up the phone by hand, this will only work properly if
you use the _same_ device you would use for dialing out. (Some people
like to create a symlink `/dev/modem' for this, but you have to be
consistent and use this for _all_ comm programs if you do - otherwise
you'll run into problems with the lock file names).

   Here are some examples for different systems:

   * SV Unix systems using the FAS serial driver:

     Use `ttyF01' etc., (minor number 80+(port number). Do _not_ use
     `ttyFMxxx'--mgetty will open the device anyway, but then an open
     to the "normal" port (without carrier detect) will block.

   * SCO Unix systems with the stock serial driver:

     Use the modem-control port (`tty2A'), _not_ `tty2a', because
     hardware flow control and carrier detection do not work on
     "lowercase" tty devices.

     The same holds for "smart" serial boards, as specialix, digiboard,
     ..., because they mimic the behaviour of SCO's sio driver.

   * Linux:

     Use `/dev/ttyS*', _not_ `/dev/cua*'. *Note Linux::.

   * SunOS, FreeBSD, NetBSD:

     Use `/dev/cua*', not `/dev/ttyS*'. Don't ask me why it has to be
     this way, but the other way won't work. (On SunOS or Solaris, you
     can find some gory details in the `man zs' man page).



File: mgetty.info,  Node: Logs,  Next: Deny,  Prev: Devices,  Up: mgetty

2.4 Log files
=============

`mgetty' will normally write all actions into a logfile, named
`LOG_PATH.<DEVICE>' (LOG_PATH is defined `policy.h'), e.g.
`/var/log/mgetty.ttyxx', so you can easily see what's happening in your
system. (If a fatal error occurs, the error message is also written to
the console, and if that is not possible, mailed to `ADMIN'). The name
of the log file can be changed in `policy.h'.

   If `mgetty' is compiled with `-DSYSLOG', auditing and error log
messages will also go to `syslog' (if your system supports it).


File: mgetty.info,  Node: Deny,  Next: Direct,  Prev: Logs,  Up: mgetty

2.5 Denying logins
==================

If you want to prevent mgetty from accepting calls, you can do so by
creating a file called `/etc/nologin.<DEVICE>' (e.g.
`/etc/nologin.tty2a'). If mgetty detects an incoming call, and sees
this file, it will _NOT_ answer the phone. This way the caller does not
lose money for a useless call when logins are not allowed anyway. (You
can change the filename that is checked by changing `NOLOGIN_FILE' in
`policy.h')

   This can be used for quite sophisticated scheduling purposes -
imagine a modem attached to a line used for voice during the daytime.
So, you want the modem only to answer the phone during 9 pm and 7 am.
What you do is to have `cron' create a `/etc/nologin.DEVICE' file at 7
am (so the modem won't answer the call during the day) and remove it at
9 pm (so the modem can answer the phone at night).

   Naturally, this can be easily extended - e.g., answer the phone only
on weekends (similar cron job), don't answer the phone if there are less
than 5 Mbyte free on disk (have a process check for free disk space
regularily and create `/etc/nologin.*' file(s) accordingly), ...


File: mgetty.info,  Node: Direct,  Next: Interaction,  Prev: Deny,  Up: mgetty

2.6 Direct serial lines
=======================

If you have a direct serial line between two unix machines, or a unix
machine and something else, and want to run a getty program on the unix
side that should not interfere with outgoing traffic (e.g.: two unix
machines, both sides running gettys, both sides able to initiate an uucp
connection), you can also use mgetty. Start it with the `-r' flag (as
with uugetty), and it will not try to initialize the modem or wait for
RINGs. It will just sit silently on the port and wait... You won't see
`/etc/issue' on the other side until mgetty gets at least one
character, this prevents two mgettys from talking to each other.

   This may be valid for leased lines with modems in leased line mode
as well, but that may depend on your modem setup.


File: mgetty.info,  Node: Interaction,  Next: Caller-ID,  Prev: Direct,  Up: mgetty

2.7 Interaction between `mgetty' and other programs
===================================================

Normally, after a caller enters his login name, `mgetty' calls
`/usr/bin/login' to do the password checking and system login.

   In some special cases, you may want to call other programs instead of
`/usr/bin/login'. For example, you could want to call
`/usr/lib/uucp/uucico -L <username>' for all login names starting with
`U*' (to have `uucico' do the authentication, works only with taylor
uucp 1.05 or taylor uucp 1.04 with my patch in `patches/taylor.p1'), or
`/usr/lib/fnet/ifcico' for incoming FidoNet calls (using `ifcico' from
Eugene Crosser's `ifmail' package).

   `mgetty' can do all this. It's controlled by a configuration file
`login.config', normally located in `/etc/mgetty+sendfax/' (definition
`LOGIN_CFG_FILE' in `policy.h'). I have provided a sample file with
lots of comments, please look into that file for the syntax to use. To
make `mgetty' understand incoming fido calls, you have to compile it
with `-DFIDO'.

   If you are worrying about security, you can also use this mechanism:
just call `/usr/bin/login' only for trusted, known users, and
`/bin/false' for every other login name - so, only those listed in
`login.config' will be able to log in.

   This mechanism can also be used to automatically start up a `PPP'
server if an incoming client sends PPP packets.  This feature is called
_AutoPPP_.  For it to work, you have to compile `mgetty' with
`-DAUTO_PPP' (added to CFLAGS in Makefile).  After this, `mgetty' will
detect incoming PPP packets, and run the program that is specified in
`login.config' by the special user name "/AutoPPP/".  See the sample
`login.config' file for an example.

   Which options should be specified depends on your PPP server program
and your local setup.  Don't ask me about that - I wouldn't know.
Instead, please check the relevant man pages.


File: mgetty.info,  Node: Caller-ID,  Next: runtime-mgetty,  Prev: Interaction,  Up: mgetty

2.8 Using Caller-ID to selectively accept or reject calls
=========================================================

Some telephone companies provide a service to the subscriber, called
"Caller ID", where the phone number of the caller is transmitted while
your phone is ringing. Not all providers support it, and you'll have to
ask for it.

   Right now, Caller ID in `mgetty' works for most modem variants out
there, ZyXEL, Rockwell, ELSA and isdn4linux among them.

   If your modem is able to retrieve callerid information, `mgetty' can
report that information by passing it as arguments to the `cid-program'
statement in `mgetty.config'. You may point `cid-program' to a script
that writes to a logfile, displays a popup on your terminal, etc.
`cid-program' takes the same arguments as `cnd-program' (see below) but
its exit code is ignored.

   In addition to the ability of reporting callerid information, if
`mgetty' is compiled with `CNDFILE' defined in `policy.h', `mgetty' can
check the caller's number before answering the phone. If `CNDFILE' is
undefined, or if the file specified does not exist, all calls will be
allowed.

   One important thing: for most analog modems, you *must* set the
number of RINGs to wait for to two (2) or higher (set `rings 2' in
`mgetty.config'), because the ID code is sent between the first and the
second RING. If mgetty picks up the phone too soon, the modem can't get
this information.

   Whether a call is accepted or denied is controlled by the
configuration file set with `CNDFILE' in `policy.h'. The usual default
is `/etc/mgetty+sendfax/dialin.config' (a sample file is installed per
default).

   That file contains a series of tokens separated by newlines, commas,
tabs and spaces. The callerid number is compared with each token in
turn, until a match occurs. A match occurs when the token compares
equally to the callerid information up to the length of the token.  If
the token is prefixed with a "!", a match means "do not answer the
phone". The token "all" matches any telephone number, and will
terminate scanning of the cndfile. If no callerid number is present, it
is assumed to have the value "none". A line starting with "#" is a
comment.  There is an implicit "all" at the end of the file.

   For example:

     	# list of my friends' data lines
     	3433535, 7445343, 5551212
     	# dad's fax
     	4164646777
     	# disallow [other] calls from numbers matching the following prefix:
     	!416
     	# disallow that speed dialer that keeps hitting my machine
     	!3444444
     	# allow all calls with the following prefixes
     	832, 555
     	# don't allow calls when there's no callerid:
     	!none
     	# It's okay to accept calls from out of area
     	# ("OUT_OF_AREA" token seems ZyXEL specific)
     	OUT_OF_AREA
     	# disallow all other calls
     	!all

   For the future, Chris Lewis is planning on adding special modem
initialization strings (e.g., 2400 bps only, fax-only, ...) dependant
on the caller number.

   For most applications, this kind of static configuration is enough.
If you have special needs, you can choose to run an external program to
decide this.  The program name is configured with the `cnd-program'
statement in `mgetty.config'.  Its command line arguments are:

       <program> <tty> <CallerID> <Name> <dist-ring-nr.> <Called Nr.>

   `CallerID' is the number of the caller, if known, or `none', if not.
`Name' is the name of the caller, or empty (") if unknown.
`dist-ring-nr.' is the RING type, if you have "distinctive RING" on
your telephone line and your modem supports this, or "0" for an
unidentified call.  `Called Nr.' is the number that was called (this is
only meaningful if you have ISDN, and your modem signals the complete
number called to the host - e.g. ELSA or ZyXEL 2864I do that).

   For example, a call from 12345 to 56789, using ISDN, coming in on
ttyS3, could lead to a program called like this:

       check.cnd ttyS3 12345 '' 0 56789

   The program return value decides whether the call should be accepted.
Currently, the following values are defined:

      0 - accept call, no specific preferences
      1 - reject call

   Future versions will allow external selection of the way
mgetty/vgetty is supposed to answer the call (data/voice/fax/...), but
that's not implemented yet.

   Note: this can not only be used to decide whether to accept a call
or not.  You could as well use it to display the caller ID on an
external LCD screen, in an X11 window, print it, initiate a D-Channel
Callback, or do whatever you want that needs the Caller ID data.

   *Note2: be careful what kind of programs you call! They run with
user id 0 (root), so that could easily be a security risk if you're not
careful.*


File: mgetty.info,  Node: runtime-mgetty,  Prev: Caller-ID,  Up: mgetty

2.9 Runtime configuration for mgetty: `mgetty.config'
=====================================================

`Mgetty' works quite well with the compiled-in defaults (it has been
the only way to configure it for a long time), but that's quite
unflexible, and especially if you use different modem types, it's
extremely unhandy.  The built-in defaults can be modified by command
line options, but that's not perfect either, because it makes
`/etc/inittab' entries very long and difficult to read.

   If compiled with _config file_ support (define `MGETTY_CONFIG' in
`policy.h'), `mgetty' can use a configuration file, quite similar to
those which "Taylor UUCP" uses, which make dynamic setup far easier.

   The config file is usually located in `/etc/mgetty+sendfax/' and
named `mgetty.config'. Its format is very simple. Each line contains one
keyword, and possibly arguments for it, separated by whitespace. Empty
lines, and comment lines (lines starting with `#') are allowed.

   The config file is grouped into port-specific sections, separated by
`port <TTY-NAME>' lines. Everything before the first `port' line
specifies global defaults, everything between two `port' statements
specifies configuration items valid only for exactly this device. Let
me show you an example:

     # global defaults:
     # fax station id is always the same
     fax-id ++49-89-1234
     # per port stuff
     port tty1a
     # This modem can't fax
     modem-type data

     port tty2a
     # more verbose logging for this modem
     debug 9

   The data part of each line, following the keyword, can be a string
(in most cases), a chat sequence (a series of strings, separated by
whitespace, that specify the "modem talk" to do. It starts with
"expect" string, then "send", then "expect" again, and so on), an
integer (interpreted as decimal, octal or hexadecimal, depending on the
leading character [1-9/0/0x]), or boolean (`y(es)' or `t(rue)' vs.
`n(o)' or `f(alse)'). If no argument is specified, this will be
considered "value not set" (if allowed) or "error" (if value is
mandatory), except for boolean values.  In that case, it's interpreted
as `true'.

   Many of those configuration items can be overriden from the command
line.  In that case, command line options take precedence over
configuration file settings (and those take precedence over built-in
defaults). In many cases, the built-in defaults can be set in
`policy.h'.

   The available configuration items are (command line options, if
available, given in brackets):

   - `speed' [-s] PORT SPEED

     Specify, as integer value, the port speed to use. Default is
     `DEFAULT_PORTSPEED'. If the given speed is not valid, `mgetty'
     complains loudly and exits.

   - `switchbd' FAX RECV. SPEED

     Some modems, mainly Rockwell chipsets, switch to 19200 bps when
     entering fax mode. Others may need other speed switches (but I
     know none).  If your modem is Rockwell based, try `switchbd 19200'
     if fax reception doesn't work. (*Warning:* if this is set wrongly,
     fax reception will definitely fail. For most sane modems, you do
     *not need* this.).  Default is `FAX_RECV_SWITCHBD'.

   - `direct' YES/NO [-r]

     Tells mgetty that it is running on a direct line. Mgetty won't try
     to initialize any modem, nor will it wait for `RING'. It will just
     wait for any character, and then output the issue file and login
     prompt. This option is used if you want to connect to machines via
     nullmodem cable.  Default is NO, since `mgetty' is designed for
     modems...

   - `blocking' YES/NO [-b]

     Tells mgetty to open the device in `blocking' mode, that is, the
     `open()' system call won't succeed until carrier detect is set.
     This is set if `mgetty' is called as `getty'. I'm not sure whether
     it's very useful, but I include it for completeness. Default is NO.

     *Do not activate this unless you understand all implications!*

   - `port-owner' USERNAME/USERID

     If set, mgetty will `chown' the tty line to the given username (you
     can specify a string or an integer uid, but the integer must be
     valid).  This is highly recommended for security purposes: only
     give port access to those users you trust not to misuse your modem
     lines! Default is `PORT_OWNER'.

   - `port-group' GROUPNAME/GID

     If set, mgetty will `chgrp' the tty line to this group id (which
     can be given as group name, or as integer gid). If it's not given,
     or not valid, the primary group id of `port-owner' will be used.
     Default is `PORT_GROUP'.

   - `port-mode' PERMISSONS

     Specifies the permissions to `chmod' the device to. *Never* make a
     modem device world-accessible, better use `0660' or even `0600'.
     Default is `PORT_MODE'.

   - `toggle-dtr' YES/NO

     Tells mgetty whether it should lower the DTR line upon startup to
     reset modem. Default is `yes', but some (few) modems react
     allergic to that and crash.

   - `toggle-dtr-waittime' MSECS

     Specifies the time to hold the DTR line low. Default is 500
     milliseconds.

   - `open-delay' MSEC

     A few modems respond to raising the DTR line (when opening the
     device) with `OK'.  This can confuse `mgetty', because it will see
     this OK as response to the next command.  In the log file, you can
     see if your modem exhibits this problem if the echo of each `AT'
     command can be seen when waiting for the response to the _next_
     `AT' command.  With `open-delay' you can give a number of
     milliseconds to wait after the device is active until `mgetty'
     flushes all incoming responses and goes ahead.

   - `data-only' YES/NO [-D]

     Tells `mgetty' to forget about faxing and only use the data part of
     the modem. Default is `false'. You need this if your modem can't
     distinguish incoming fax and data calls.

   - `fax-only' YES/NO [-F]

     Tells `mgetty' to put the modem in fax-only mode. You need this if
     your modem can't distinguish incoming fax and data calls, but you
     need fax more important than data; and you need it if you want to
     disable data calls for security reasons (this could be achieved
     via `login.config' as well)

     Watch out: if you have setup some unusual `answer-chat', incoming
     calls might still come through. So check your setup!

   - `modem-type' [-C] MTYPE

     Specifies the kind of modem connected to the port. Default is
     `DEFAULT_MODEMTYPE'. Valid options are:

        * auto

          Mgetty will detect the modem type itself (which may
          occasionally be not desirable, or it may fail on old modem
          equipment).  Mgetty will use the `ATI' command to find out
          the modem type, and select the proper fax class accordingly.
          If that fails (unknown modem type), mgetty will try class 2.0
          and then class 2.

        * c2.0

          Modem is a CLASS 2.0 fax mode. Works better than class 2, if
          both are available, because its better standardized. Known to
          work with USR, ZyXEL 1496 and 2864 series, and ELSA modems.

        * cls2

          Modem is a CLASS 2 fax modem, mgetty will not try class 2.0.

        * c2.1

          Modem conforms to the new ITU T.32 standard (class 2.1).  To
          my knowledge, there are no such modems available yet, but
          supporting them will be easy as class 2.1 is very similar to
          class 2.0.

        * cls1

          Modem can only do class 1 fax.  NOT IMPLEMENTED YET.  (And
          not recommended anyway).

        * c1.0

          Modem can do class 1 fax conforming to ITU T.31 standard.
          This isn't much better than class 1 (use class 2 / 2.0 if
          available!), but is better standardized.  NOT IMPLEMENTED YET.

        * cls2ok

          (obsolete, use `modem-quirks 02')

        * data

          Do not try fax initialization, same as if `-D' given.

     There is no way (yet) to tell mgetty to use *only* fax mode and
     refuse data calls with this option, use the `fax-only true'
     statement for that.

   - `modem-quirks' BITMASK

     Some modems have a very peculiar interpretation of the fax
     standards.  Some of the internal operations of `mgetty+sendfax'
     can be adapted to that.  The argument is a number, constructed
     from valies in `fax_lib.h', one bit per "quirk".  Usually you
     won't need this option, because those modems really needing it are
     auto-detected and handled properly anyway.

     Right now, the following quirks are defined:
          0x01  leave the modem in class 2 mode instead of switching
                to class 0 before sending ATA (you might try this if
                adaptive fax/data answer doesn't work).
          0x02  class 2 bit order is correct (MultiTech) - unimplemented
          0x04  do not trust +FPTS:x,lc,blc values
          0x08  do not wait for XON character when sending pages
          0x20  AT+FCC/+FMINSP bug workaround for (very) old USR Courier V.32
          0x40  display incoming informations about 'non standard frames' - this
                might be necessary on some USR modems to work around logic bugs

   - `init-chat' [-m] EXPECT SEND EXPECT SEND ...

     Tells mgetty the chat sequence to use for initializing the modem.
     *Warning*: the sequence starts with *expect*, which will in most
     cases be `""' (nothing). This ordering was chosen because UUCP
     does it this way, and I wanted to avoid confusion here.

     Example:

          init-chat "" ATQ0E1V1H0 OK ATL0M0S0=0 OK AT&K3 OK

   - `force-init-chat' EXPECT SEND EXPECT SEND ...

     In some cases, the modem can get stuck in a mode where it won't
     react to a simple `AT' command. Usually this happens because the
     modem is set to ignore a DTR drop and still has a data connection
     to the other side. If you use a voice modem, it could be stuck in
     voice mode.

     In these situations, the normal `init-chat' will time out, because
     the modem won't send the proper responses back.

     To get the modem back into a sane state, you can use the
     `force-init-chat' chat sequence. The default setup will send the
     DLE ETX characters, to get voice modems back to life, and then the
     `(pause)+++(pause)ATH0' sequence to get the modem back from data
     mode to command mode.

     You could prepend this sequence to `init-chat' (it wouldn't harm),
     but especially the pauses around the +++ sequence makes this
     undesirable slow.

   - `post-init-chat' EXPECT SEND EXPECT SEND ...

     Some modems forget parts of their settings when going from data to
     fax mode and back during modem initialization.  For example, some
     USR models forget the settings of "Caller ID delivery" (AT#CID=1),
     and some ELSA modems forget their current DTE port speed when
     going from voice to data mode, thus leading to RING messages being
     delivered with the wrong baud rate.

     For those modems, you can use this command to set up some AT
     commands that are executed after all other fax and voice
     initialization has been done.  Be careful with what you do!  If
     you send an ATZ (modem reset) or something similar here, all your
     fax/voice settings will be lost!

   - `modem-check-time' SECONDS

     Some modems have the nasty tendency to crash silently. With this
     option, you tell `mgetty' to check every SECONDS seconds with a
     simple `AT...OK' sequence whether the modem still reacts. If not,
     `mgetty' will restart itself and do a full modem reset. Default is
     `MODEM_CHECK_TIME'

   - `rings' [-n] NNN

     Sets the number of `RING' messages to wait for, before mgetty
     picks up the phone. Default is 1. *Warning:* if your modem
     auto-answers, for whatever reason, set this to something
     *different* than the value set with `ATS0=mmm', otherwise the
     modems autoanswer and mgettys manual answer will collide (most
     modems hang up if a command is received during auto-answer)

   - `msn-list' MSN1 MSN2 MSN3...

     If you have an ISDN modem that signals the called party number
     (MSN) to the host, you can use this statement to map the MSN
     numbers to distictive RINGs.  The MSN called will be compared the
     list, and the first match is used for the distinctive RING number.
     The list is searched from left to right.

     This is known to work with ELSA and ZyXEL ISDN terminal adaptors.

   - `get-cnd-chat' CHAT SEQUENCE

     This is needed if you have a modem that supports "caller ID"
     detection, but needs a special command to get the CID information.
     Right now, this is only needed for some ELINK ISDN adaptors (*note
     Elink-ISDN::), most other CID-capable modems send the CID on their
     own and don't need this.

     Don't forget to set `rings' to at least 2, otherwise the CID
     grabbing code won't work.

   - `cnd-program' PATHNAME

     Specify a program to be run before answering an incoming call.
     Use this if the static Caller ID selection in CNDFILE (policy.h)
     is not sufficient, or if you want to use the Caller ID data for
     other purposes (displaying, for example).  *Note Caller-ID::.

   - `cid-program' PATHNAME

     Specify a program to be run as soon as Caller ID information comes
     in (typically between 1st and 2nd ring). If Caller ID info is not
     available by the 3rd ring, still run the program (to report the
     time that the phone rang).  This allows mgetty to behave like a
     caller-id box. *Note Caller-ID::.

     The return value of `cid-program' is evaluated as follows:

           0 - handle call normally
           10+n - set number of RINGs to wait for to "n", then proceed

     so you can use that to have `mgetty' answer the phone right away
     for known fax-callers (or voice spammers), and only after 8 rings
     for everyone else.

   - `answer-chat' CHAT SEQUENCE

     This is the command sequence that is used to answer a phone call.
     Usually you can leave it at the default ` "" ATA CONNECT \c \r ',
     but for some modems you need `ATS0=1' in place of `ATA' (ATA not
     allowed). The extra `\r' expect string is needed that the code can
     grab the full CONNECT XYZ\R string. It will work without the \r,
     but then the logging information will be less detailed. *Right now,
     \r won't work at all, it's not implemented yet. Don't use it.*

   - `answer-chat-timeout' SECS

     During the ANSWER-CHAT, each "expect" string must be seen in the
     time specified here. Default is 80 seconds. This time should be at
     least some 5 seconds longer than the time set with the `ATS7=...'
     modem setup command.

   - `autobauding' YES/NO [-a]

     Some modems switch their DTE line speed to the communication line
     speed after connecting, e.g., after sending `CONNECT 2400', the
     modem switches to 2400 bps. Newer modems usually have a switch to
     "lock" a DTE baud rate, which is strongly recommended. If your
     modem insists on doing this speed switch, setting `autobauding' to
     TRUE will make mgetty behave accordingly.

   - `ringback' YES/NO [-R]

     If you have to put your modem and your telephone on the same phone
     line, you can switch on "ringback" or "ring-twice". This means,
     mgetty won't answer the phone on the first call, but remember the
     call, and pick up on the second call (if it comes in the time
     specified by `ringback-time').

   - `ringback-time' SECS

     This setting specifies how much time may pass between the first
     and the second call if "ringback" is active. Default is 30 seconds.

   - `ignore-carrier'

     If your Modem does not assert the DCD (carrier detect) line, or the
     serial port or cable or serial driver is broken, it is possible
     that `mgetty' or `login' will block after a successful CONNECT
     (that means: everything seems to work, but suddenly nothing is sent
     to the port anymore. Depending on the operating system used, this
     can be before printing the `/etc/issue' file or not before printing
     the `password:' prompt.

     To work around this, you can switch off the carrier detection in
     the kernel: set `ignore-carrier true'. Default is `false'.

     *WARNING:* If you use this, your system won't be able to detect
     when a caller just hangs up instead of cleanly logging out. This
     may result in hanging modems, etc.

   - `issue-file' [-i] FILE

     This is the file printed before the login prompt. Default is
     `/etc/issue'.  Some special characters are substituted by connect
     speed, date, etc. - see below (login-prompt) for a list.

     Note: maximum line length after substitution is 300 characters, so
     be careful with ASCII art banners with lots of color settings and
     such.

   - `prompt-waittime' MSECS

     This specifies how long `mgetty' will wait for modem and line to
     settle down before printing issue file and login prompt. Default
     is 500 milliseconds.

   - `login-prompt' [-p] PROMPT

     This specifies the login prompt that mgetty will output. Some
     special characters in this string (and in the issue file, btw) are
     recognized and replaced by something else:

        * @ system name

        * \n newline

        * \r carriage return

        * \g bell

        * \b backspace (ascii 010)

        * \f form feed (ascii 013)

        * \t TAB

        * \s operating system (OS)

        * \m hardware name

        * \V OS version

        * \R OS release

        * \P (and \L) port name (e.g. ttyS0)

        * \C date and time, in "ctime()" format

        * \I Connection string (e.g. 2400/REL)

        * \N (and \U) number of users currently logged in

        * \S Port speed (e.g. 38400)

        * \D current date in dd/mm/yy format

        * \T current time in hh:mm:ss format

        * \Y CallerID of the current caller

        * \DIGIT character with the specified octal code

     The maximum lenght of the login prompt is limited to 300
     characters (after expansion).

   - `login-time' SECS

     This specifies the maximum time the user can take to log in. If no
     login has occured after that time, `mgetty' will hang up. Default
     is `MAX_LOGIN_TIME' from `policy.h'.

   - `login-env-ttyprompt-hack' YES/NO

     On SVR4, maybe on other systems too, you can cause the 'login'
     program to prompt with the same string as mgetty did, instead of
     the standard "login:" prompt. The string will be passed to the
     'login' program in the environment variable TTYPROMPT.  This is
     done by putting "login" into a special (brain-dead) "ttymon"-
     compatibility mode. In that mode, mgetty doesn't ask for a login
     name at all, so mgetty won't work if you enable that feature and
     your login program doesn't support it. You can see if it doesn't
     work if the user gets a double login prompt or none at all.

     As a side effect, this feature can also be used to directly start
     "other" applications, like a BBS software or similar things, after
     the modem has connected (login.config would then be used to
     specify what program to run.)

     This feature is incompatible with FIDO and AutoPPP support - those
     work only if mgetty can see the user response to the login prompt.

     In previous releases, this used to be `ENV_TTYPROMPT' in
     `policy.h'.

   - `fido-send-emsi' YES/NO

     Only relevant when mgetty was compiled with `-DFIDO'. Controls
     whether mgetty should send a FidoNET style "EMSI_REQA77E" packet
     before prompting for login. Default is on. Switch this off if you
     have FIDO support compiled in but experience weird problems with
     some PPP clients (or users!) being confused by that string.

   - `login-conf-file' PATHNAME

     Specifies the path and filename of the 'login.config' file that
     tells mgetty which program to call for login.  See the example
     login.config file to get some ideas what to do with it.

     The file name given will be ignored for security reasons if the
     file is not owned by 'root', or is readable or writeable by
     anybody else than 'root' (that is, it must be mode 0600 or 0200).

   - `fax-id' [-I] LOCAL FAX NUMBER

     This sets the fax station ID used in fax mode to identify your
     site to the caller (usually this is simply your fax phone number).
     Default is `FAX_STATION_ID'.

   - `fax-server-file' [-S] POLL CONTROL FILE

     Specifies the fax file(s) that is to be sent if someone else calls
     your modem in _fax polling mode_, that is, the caller _receives_ a
     document.

     Normally, the file given is a text file, containing the list of G3
     files to send to the calling machine, one file per line. Comment
     lines (starting with "#") are ignored. For backward compatibility,
     `mgetty' does check whether the named file is a G3 file itself, in
     which case this file is sent directly (but then, you can only send
     one page).

     Not all modems support fax poll _server_ mode, I know that the
     ZyXEL and MultiTech do, and USR does not.

   - `diskspace' [-k] KBYTES

     This setting tells mgetty the minimum amount of disk space that
     has to be available in the fax spool directory for fax reception
     to be allowed.  Default is 1 Mbyte.

   - `notify' MAIL ADDRESS

     This is the address that will get mails if a fax is received.  If
     you do not want e-mail notification, specify `notify' without an
     e-mail address.

   - `fax-owner' USERNAME/UID

   - `fax-group' GROUPNAME/GID

   - `fax-mode' PERMS

     Similar to `port-owner/group/mode', these settings specify the
     owner, group and file mode mgetty will use for incoming faxes.
     Defaults are taken from `FAX_IN_OWNER', `FAX_IN_GROUP', and
     `FAX_FILE_MODE'.

   - `fax-spool-in' DIR1:DIR2:DIRN

     Specifies a directory, or list of directories, where incoming
     faxes are saved.  Multiple directories are tried in order until,
     the first one that has enough disk space and is writeable is used.

     The default setting is taken from `FAX_SPOOL_IN' in the Makefile
     usually `/var/spool/fax/incoming:/tmp' (/tmp is used as fallback).

   - `debug' [-x] DEBUG LEVEL

     This sets the amount of logging `mgetty' will do. A good value is
     4, more details are seen with `5', and `9' is really noisy.  Try
     it! The log data is written to the file specified by `LOG_PATH' in
     `policy.h', usually this is something like `/var/log/mgetty.ttyxx'.

   - `gettydefs' GD TAG

     If you use the gettdefs feature of `mgetty' - which is _not_
     recommended! - this specifies the gettydefs tag to use for the
     given line.  See MAN GETTYDEFS, MAN MGETTYDEFS.

   - `term' TERMINAL TYPE

     If you are on Linux or similar OSes that have `getty' set the
     `TERM=xxx' terminal type variable, and have no other method to set
     it (e.g. from `/etc/profile' or `$HOME/.profile'), `mgetty' can do
     it for you. Just specify ``term' vt100' or so. I don't think it's
     a good idea to specify the terminal type on a per line base (what
     if all your callers use different terminal types?), so the default
     is UNSET.



File: mgetty.info,  Node: Fax,  Next: voice,  Prev: mgetty,  Up: Top

3 Fax Operations
****************

Both mgetty and sendfax deal exclusively with raw "g3" fax files ("g3"
stands for "group 3", which is the CCITT standard for encoding images
for fax transmission). You will have to use external programs to
create, view or print these.

   There are two kinds of g3 files, the high resolution type with
204x196 dpi and the low ("normal") resolution ones with 204x98 dpi.  If
you mix up the two, the recipient will get a fax page that is either
twice or half the proper length. You have been warned.

   The width of a fax page is always 1728 pixels, the length is
arbitrary (though there are some plain paper fax machines out there
that limit the page length to A4 paper). A typical full page has a
length around 2100 pixels in high-resolution mode.

* Menu:

* Convert::         Converting fax files
* Receiving::       Receiving faxes
* Sending::         Basic `sendfax' usage
* Polling::         Fax polling using `sendfax'
* Queuing::         Automated fax queuing
* Fax-Tools::       Additional tools provided for handling g3 files
* Scanner::         Using an external fax as a scanner
* runtime-sendfax::  Runtime configuration: `sendfax.config'


File: mgetty.info,  Node: Convert,  Next: Receiving,  Prev: Fax,  Up: Fax

3.1 Converting fax files
========================

I recommend getting the `pbmplus' package written by Jeff Poskanzer,
which includes lots of small programs to convert various bitmap formats
into a portable intermediate format (`pbm') that can easily be
converted to fax format with the `pbm2g3' program. Further, it comes
with lots of tools to scale, flip, and otherwise manipulate the `pbm'
bitmaps. Be warned: it includes its own version of G3 conversion
programs (`pbmtog3' and `g3topbm'), so be careful which one you use.
The programs in the `mgetty' package (`pbm2g3' and `g32pbm') behave
slightly different (that is, they work!), and are significantly faster.
Note that the `pbmplus' package does not include a graphical front end.

   The `pbmplus' package can be found on most major FTP sites, e.g. on
ftp.x.org in the `/contrib' directory. *Note ftp::.

   If you want to view the images using X11, you should get one of the
many image viewers, like `xview', `xloadimage' or `xv'.  *Note
Fax-Tools::. A simple, but very fast fax viewer can be found in
`mgetty/frontends/X11/'.

   Here are some examples for viewing fax files using `g32pbm':

   * You can print a fax on a PostScript printer (try `lpr -Pps' if you
     don't have `lp'):

          cat $faxfile | g32pbm | pnmtops -noturn | lp -dest postscript

   * or on an Epson-LQ, scaled for fine resolution (use -yscale 1.84 for
     normal resolution):

          cat $file | g32pbm | pnmscale -xscale 1.76 -yscale 0.92 |\
              pgmtopbm | pbmtodot -360x180| lp -o epson -

   * or you could view it using X11 via one of the following commands:

          $ viewfax -v $file

          $ cat $file | g32pbm >/tmp/fax.pbm ; xloadimage /tmp/fax.pbm

          $ g32pbm $file | xv -


   There are three easy ways to create g3 fax files, either use `pbm2g3'
(included in this package. Do not use `pbmtog3' from the pbmplus
toolkit. *Note pbmtog3::.), use GhostScript (GNU Software, can be found
on prep.ai.mit.edu) which contains a "digifax" driver that will produce
the required format, or try Chris Lewis' `hp2pbm' package which will
convert HP Laserjet print files into g3 fax files (`hp2hig3' program).

   Once you have the right tools, there are lots of ways to create fax
files for a wide variety of applications. Here are some examples:

   * Ascii files can be converted using `pbmtext | pbm2g3' (use a
     _large_ font, and don't convert texts longer than about 50 lines).
     Alternatively, you can convert ascii files to PostScript using
     `psify', the `pslp.ps' program from the ghostscript distribution,
     or similar tools, and feed their output into GhostScript.

   * PostScript input can be converted by GhostScript (version 2.4 or
     higher), using the digifax (`dfaxhigh' and `dfaxlow') drivers.  It
     will generate a plain g3 file with a 64 byte additional header,
     which will be skipped automatically. (You have to generate
     separate g3 files, one per page).

     A typical call to ghostscript would look like this:

          gs -sDEVICE=dfaxhigh -sOutputFile=/tmp/fax.g3.%d yourdocument.ps

     Do _not_ use the "tiffg3" or similar drivers, they will create
     output files with headers that sendfax does not understand, thus
     causing the receiving fax machine to reject the data (it will
     assume that the transmitted headers are garbled data).

     If you use Ghostscript version 3.01 and up, you can use the `faxg3'
     driver as well, its output is identical to the output of the
     `dfaxhigh' driver except for the 64 byte header.  Besides this,
     there should not be any difference.

     I have observed that with Ghostscript 5.01, the output of the
     `faxg3' driver is rendered better than that of the `dfaxhigh'
     driver. In addition, the former is compiled-in by default, while
     the latter is not.  Thus, the default driver used by `faxspool' is
     now (starting with 1.1.7) the `faxg3' driver.

   * Bitmaps can be converted using the `pbmplus' tools, but you'll have
     to do the proper scaling by hand. Use a pipeline with `pbm2g3' at
     the end.

   * TeX dvi files can be converted to PostScript using `dvialw' or
     `dvips'. If you want to get the best possible output quality, you
     can use Metafont to create a set of 204x196 dpi fonts, which will
     look a lot better than scaled 300 dpi fonts (look into
     `contrib/dvi-fax' for instructions how to do this). You can use
     the `epsf' macros to include encapsulated PostScript files, e.g. a
     scanned signature.

   * Another way for TeX file conversion is Ralf Schleicher's `faxdvi'
     package, found at
     `ftp://ftp.leo.org/pub/comp/os/unix/networking/mgetty/faxdvi-1.1.tar.gz'.
     Don't ask me about, ask him!

   * HP-Laserjet files can be translated with Chris Lewis' `hp2pbm'
     package. It contains a program `hp2hig3' that will read
     HP-Laserjet `PCL4' files and produce G3 output.

     *Warning:* the G3 files that hp2hig3 emits lack the leading EOL
     code, thus causing `sendfax' to complain and possibly fail. As a
     quick fix, you can pipe those files through `g3cat', it will fix
     the data.


   A rather crude sample conversion program (`faxcvt') is provided in
the fax directory.

   Better conversion, including guessing of the format of the input
files, is done by the `faxspool' program, also provided in the fax
directory. *Note Queuing::.


File: mgetty.info,  Node: Receiving,  Next: Sending,  Prev: Convert,  Up: Fax

3.2 Receiving faxes
===================

If everything has been set up properly, faxes will be received
automatically. Obviously, mgetty has to be listening to the proper modem
line. Then, if a fax arrives, mgetty will store it in the directory
`FAX_SPOOL_IN' (or the directory configured in `mgetty.config', *note
runtime-mgetty::) and send a mail to `MAIL_TO' (defined in `policy.h').

   The file name format is somewhat tricky (the reason behind it is
that I have to create something unique without using `mktemp()',
because that would make it impossible to find out which pages belong to
which fax). It is:
     f<res><seq><line>[-<remote id>].<pagenr>
   `<res>' is `n' or `f', depending on the resolution of the fax.
`<seq>' is a sequence number, 7 digits wide, somewhat related to the
reception time. `<line>' are the last two letters of the tty device,
e.g. `S1'. If the sending side specified a fax station id, it comes
next, after a leading dash (all blanks are replaced by dashes).
Finally, after a dot, you'll see the page number.

   If you want to process incoming faxes automatically, for example,
print them, re-send them to another fax, send them by mail to you when
you're on vacation, you could use what I call "notify programs":

   If you define `FAX_NOTIFY_PROGRAM' in `policy.h', mgetty will call
this program (or shell script) when a fax has been completely received.
It will be called with the following command line arguments:

     FAX_NOTIFY_PROGRAM <HANGUP CODE> '<SENDER ID>' <NR OF PAGES> \
                        <FILE NAME PAGE 1> <FILE NAME PAGE 2> ...

   <HANGUP CODE> is 0 if the receive was successful, non-zero
otherwise.  <SENDER ID> is the fax identification string received from
the other side.  <FILE NAME PAGE 'I'> is the full path name for each
received page.

   A sample command line might look like this:

     /usr/local/bin/new_fax 0 "+49 89 3243328" 1 /var/spool/fax/ff-01.a123

   In addition, some environment variables are provided: `CALLER_ID',
`CALLER_NAME', `CALLED_ID' (Caller ID and destination ISDN MSN, if
available and supported by your modem), `CALL_DATE', `CALL_TIME', and
`DEVICE' (the full name of the tty device, if you want to process faxes
differently depending on the line they came in).

   Such a "notify program" could print out the fax, convert it into a
MIME metamail and send it away, display it in an X window (this a
little bit tricky), or whatever. (A friend of mine uses it on his Linux
box to call a program that will make the keyboard LEDs blink when a fax
has arrived - as you can see, maximum flexibility is possible).

   I provide a few examples (printing on HP laserjet, mailing as
gzip'ed, uuencoded pbm file, ...) in `samples/new_fax.*'

   If you have the `dialog' shell tool, you can use the `faxv' program
("faxview") that I provide in `frontends/dialog/faxv' to browse through
all faxes in the incoming spool directory, view them, print them,
rename and move them, .... `faxv' is really more a sample program to
show you how to do it, and you have to configure the X11 viewer and the
printing program in the source code, but I use it for my faxes, and it
works. Because of limitations on some operating systems, the list of
faxes displayed is limited to the last 50 faxes received.


File: mgetty.info,  Node: Sending,  Next: Polling,  Prev: Receiving,  Up: Fax

3.3 Basic `sendfax' usage
=========================

Sendfax is very primitive--no spool management, no format conversion,
etc.  It is designed to be able to send exactly one fax (consisting of
multiple pages) to exactly one fax machine, but it is usable from
within shell scripts.  Its input are pages in "g3" format, either
created with ghostscript or with pbm2g3.

   It is called like this:

     sendfax [-v] [-n] <PHONE-NUMBER> <FAX PAGE(S)>

   e.g.

     sendfax 0893243328 /tmp/to_gert_1.g3 /var/spool/fax/outgoing/picture.g3

   It will then attempt to open the fax device and send all the pages to
the remote fax machine, in the given order.

   It will print little or nothing to stdout or stderr, except if it
cannot find or open one of the named files, or if some transmission
errors occur.

   (There are a few stubs in the code to put headers on the pages at
run-time, but since most class 2 faxmodems do not implement the command
set properly, putting a header on a page does not work with them -
because of that, I had to disable the corresponding code. `faxspool'
works around this problem by using `g3cat' (*note Fax-Tools::) to
"paste" a header line on top of each page)

   If you specify `-v', sendfax will output more verbose progress
messages.

   If you specify `-n', it will try to send the fax data in normal
resolution, default is fine resolution. (No conversion is done, so make
sure that your input data is already in the proper format.)

   Detailed reports can be found in the log file (usually
`/var/log/sendfax.log') -- but they may be of little more than
technical interest since virtually all conversation with the fax modem
is logged. (Nevertheless, if you send me any bug report, _please include
all log files_)

   *Warning:* Watch sendfax closely when sending the first few faxes. I
had it abort a transfer a couple of times, not being able to recover
and _not_ hanging up the modem (the modem was completely locked up,
with the phone line off-hook)! In my case, it was a problem of the
modem that went away when I upgraded the firmware. Very old ZyXEL
releases sometimes stopped the DTE and forgot to re-start it again.

   The return codes of the sendfax program were chosen to make it easy
for external programs (i.e. faxrunq) to decide whether to try again or
not:

      0: all pages transmitted successful
      1: error on command line
      2: cannot open fax device (typically happens if fax device is
         locked, but could also be a permission problem)
      3: error initializing the modem
      4: dial failed, "BUSY"
      5: dial failed, "NO DIALTONE"
     10: dial failed, "ERROR" or "NO CARRIER"
     11: waiting for XON failed (should never be seen)
     12: transmitting page(s) failed (or polling failed)
     15: some catastrophe hit (termination signal or blocked modem)

   If the error code is less than 10, the attempt didn't cost anything,
so an external program should try again to send the files. If it is 10
or higher, the failed attempt probably cost something, and the program
should decide whether to try again (thus expending more money) or mail
the operator and tell him something went wrong. My `faxrunq' program
will suspend the job after five unsuccessful tries with error codes >=
10.


File: mgetty.info,  Node: Polling,  Next: Queuing,  Prev: Sending,  Up: Fax

3.4 Fax polling using `sendfax'
===============================

Sendfax can also be used for fax polling (that is, you call someone and
initiate a fax connection, and then _receive_ a document. Don't confuse
it with fax-on-demand, this is something different), the syntax is:

     sendfax -p <FAX-NUMBER>

   or for sending a fax and then switch to polling:

     sendfax -p <FAX-NUMBER> <SEND-DOCUMENTS>

   (in this case <SEND-DOCUMENTS> are sent, and then the documents from
the other modem are polled, if there are any)

   the received pages are written to the current directory, so make sure
you have write access...

   *Warning:* Fax polling does _not_ work with ZyXEL Modems with ROM
releases before 6.00 - with the 6.01 and 6.10 Eproms it works, but
6.11a is broken again. 6.12 and 6.13 work fine.

   It definitely doesn't work with some Rockwell-based Faxmodems
(Supra), since many versions of this chipset does not support polling.
Some work, though, so you simply have to try it.

   Could anybody try this with an Everex Faxmodem?


File: mgetty.info,  Node: Queuing,  Next: Fax-Tools,  Prev: Polling,  Up: Fax

3.5 Automated fax queuing
=========================

For fax spooling and processing the queue, four additional utility
programs are provided:

   * `faxspool' will spool a number of files (accepting various formats)
     and put them into the fax spool directory. Its syntax is:

          faxspool [options] phone-number input-file(s)

     `phone-number' can be an alias, in this case the private and global
     alias files `$HOME/.faxnrs' and `/etc/mgetty+sendfax/faxaliases'
     will be searched for a line starting with this alias. The
     remainder of this line will then be used as fax number.

     `faxspool' interacts with the `file' program and `/etc/magic' to
     determine the file type of the input files. If your `/etc/magic'
     lacks entries for the various bitmap files, take a look at
     `fax/etc-magic', it contains the most important magic numbers.

     `faxspool' reads the text to put on top of each fax page from a
     text file. The text file is (in order of precedence) the argument
     of the option -h, the `$HOME/.faxheader' and as system-wide default
     `/etc/mgetty+sendfax/faxheader'. This file must contain pure ASCII
     text. Some tokens are replaced by the actual values: @T@ becomes
     the destination phone number, @P@ becomes the actual and @M@ the
     total page number, and @U@ is replaced by the user name. If your
     fax modem cuts of a few lines on top of each page, it may be a good
     idea to put a blank line before the header line itself, and it is
     also a good idea to indent the line about 5 spaces.

     For the available options, please read the `faxspool.1' man page.

   * `faxrunq' will read this directory and try to send all the faxes
     queued there (time scheduling is available, but primitive). If
     faxrunq succeeds, the fax is deleted and the sender is mailed. If
     it does not succeed after five tries (`BUSY' or a locked fax modem
     do _not_ count for this) it will send a mail and not try any
     further to send this fax. (This should prevent your faxmodem from
     making you bancrupt...).

     `faxrunq' should be called at regular intervals from `cron' to
     process the queued jobs. It should only be executed by _root_, to
     make sure that all the files in the fax spool directory are read-
     and writeable.

   * `faxq' will display all entries in the fax queue. If called with
     the `-o' parameter, it will also display completed, but not yet
     deleted jobs (JOB.done files). If called with the `-v' parameter,
     the output will be more verbose.

     Jobs that are just being sent are not shown (`faxq' doesn't see
     locked jobs)

   * `mgetty-faxrm' can be used to remove fax jobs from the queue. It
     is called with the job ids of the to-be-removed faxes as command
     line argument. The job ids are those that `faxq' returns.


   These utilities do still have some rough edges, but I think they are
fairly usable by now.

   Earlier variants of those utilities had to be configured in the
source code, from release 0.20 on, this is done by `make'. Please check
the scripts nevertheless, whether all directories and files are set up
properly.


File: mgetty.info,  Node: Fax-Tools,  Next: Scanner,  Prev: Queuing,  Up: Fax

3.6 Additional tools for working with g3 files
==============================================

Some additional tools are provided for manipulating G3 fax files:

   * `g3cat' (in the `g3/' directory) concatenates multiple G3 fax
     files. It accepts "raw" g3 files and digifax files and outputs a
     "raw" g3 file without headers. Its syntax is analogous to `cat',
     except that you _have_ to specify `-' to read from `stdin'.

     `g3cat' recognizes two flags: `-l', to separate the fax files with
     a thin black line, and `-a' to byte-align the end-of-line codes in
     the file (Warning: some modems do not like this).

   * To convert an incoming fax to Jef Poskanzers `portable bitmap'
     (`pbm') format, you can use the `g32pbm' program that is also
     provided in `g3/'. It's advantages over Jef's `g3topbm' program
     are that it's approximately five times faster and takes only one
     eigth as much virtual memory (on machines with low virtual memory,
     it can thus be up to 100 times faster!). Its disadvantage is that
     it produces only "raw" (i.e., binary) `pbm' files; and it's not as
     stable when handling erroneous `g3' data (means that if one line
     is severly corrupted, it can happen that the next line will not be
     decoded properly. The rest of the file will then be OK again).

     Syntax:
          g32pbm [-r] [-s] [-l] [-d <dpi>] [g3-file]

     If no g3 file is specified, standard input is used.

     The `-s(tretch)' option causes `g32pbm' to double each row of the
     g3 file.  You can use this to adjust the aspect ratio of a "normal"
     resolution fax file to match that of a "fine" resolution fax.  Of
     course you can use other `pbmplus' tools for this instead, but
     `-s' is sure to be faster.

     If you have a HP Laserjet printer, you can make `g32pbm' output HP
     LJ data with the `-l' switch. The desired resolution is chosen with
     the `-d 75|150|300' switch.

   * For the other direction, I have provided a `pbm2g3' program that
     will convert Jef Poskanzer's Portable BitMap format into G3 fax
     data suitable for faxing with `sendfax'. The `pbm' files can be
     produced by various sources, e.g. drawing programs (`xpaint'),
     bitmap manipulation programs (`xv'), or simply be converted from
     other file formats by means of the `pbmplus' tools.

     As above, my variant is a lot faster than Jef's, and unlike his, it
     produces g3 data that adheres to the T.4 standard (if you don't
     fiddle too much with the options...), so you don't have to apply
     any patches to make it work together with `sendfax'.

     Syntax:
          pbm2g3 [-r] [-a] [-w page with] [-h blank lines] [pbm-file]

     if no pbm file is specified, standard input is used.

     For a detailed description, see the `pbm2g3(1)' man page.

   * `viewfax'. To view G3 data files under X11, Frank D. Cringle has
     written a very nice and fast tool that will display the files on
     screen, turn them, zoom them in and out, ...

     The source code can be found in the `mgetty/frontends/X11'
     directory.  It's not (yet) built and installed by default, but
     it's straightforward.

     For a detailed description, see the `README' and `viewfax.man'
     files in that directory.

   * To convert an incoming fax into X-Windows `xwd' bitmaps, you can
     use Chel van Gennip's `g3toxwd' program, found in the `contrib/'
     directory.

   * If you want to print out faxes on a HP laserjet printer, you have
     two opions: you can use Chel's `g3tolj' program (also in the
     `contrib/' directory), or you use my `g32pbm' program with the
     `-l' option, which will make it output LJ data.



File: mgetty.info,  Node: Scanner,  Next: runtime-sendfax,  Prev: Fax-Tools,  Up: Fax

3.7 Using an external fax as a scanner
======================================

It is possible to tell mgetty to answer the phone even if it is not
ringing (I call this "virtual rings"). Just send mgetty a signal
`SIGUSR1', this is usually done with `kill -USR1 <MGETTY-PID>'.  Mgetty
will then pick up the phone and try to make a connection.

   If you have a normal fax machine connected to the fax modem, it
should be possible to have that fax machine dial any digit (to turn off
the dial tone), and then have mgetty answer the phone to receive the
"incoming" fax, thus using the fax machine as scanner without paying
for a call. For a description of an sample setup (thanks, caz!), please
see `doc/scanner.txt'.

   Whether it works may depend on your phone company's setup, but it
should.

   If you have a modem that has a `data/voice' button, it should also be
possible to hit that button to make the modem pick up the phone. Mgetty
will automatically notice that and handle it properly. (I've tested this
only with ZyXELs - could somebody else please test this with other modem
types and send me a logfile? Thanks)


File: mgetty.info,  Node: runtime-sendfax,  Prev: Scanner,  Up: Fax

3.8 Runtime configuration for sendfax: `sendfax.config'
=======================================================

Basically, `sendfax' can work very well with the compiled-in defaults
(from `policy.h'), sometimes slightly modified by command line options.

   If you use more than one fax modem, possibly of different type, this
is very awkward, because the command line will get very long. For that
reason, there is a configuration file which will control nearly every
detail of sendfax' behaviour.

   It is usually named `/etc/mgetty+sendfax/sendfax.config'.

   The config file consists of multiple sections, separated from each
other by the keyword `port'. All configuration options given before the
first `port' statement specify global options, and everything between
two `port' statements applies only for the device with the given name
(`port' takes an argument). Let me show you an example:

     # global defaults:
     # fax station id is always the same
     fax-id ++49-89-1234
     # always have the speaker on
     modem-init ATM1L3

     # port specific: for /dev/tty1a, switch the speaker off
     port tty1a
     modem-init ATM0L0

     # port specific: for ttyS1, use another fax station id
     port ttyS1
     fax-id ++1234567

   As you can see, empty lines and comment lines (starting with "#") are
allowed.

   Every line in the config file that is not a comment - or empty -
starts with a keyword (listed in detail below), followed by a "data"
field. In the example above, `fax-id' is the keyword, `++49-89-1234' is
the corresponding data, the fax ID for the sending machine. Most data
fields are strings, but there are a few boolean and integer items.

   The available keywords are (if it's possible to set this item from
the command line, the flag is given in brackets).

   - `fax-devices' [-l] TTYS

     Sets the fax modems to use, e.g. `tty1a:tty2a'. Default is
     `FAX_MODEM_TTYS' from `policy.h'. The device names given here are
     used to look up the corresponding `port' section later. Watch out
     for upper-/lowercase.

     It is not very useful to specify this in the per-port section, so
     it is ignored if met there.

   - `modem-init' [-m] COMMAND

     Specifies an `AT...' command that is to be sent to the modem right
     at the *beginning* of all modem talk (even before setting the modem
     into fax mode, so this could be an `ATZ' if you want to reset the
     modem).

   - `modem-handshake' COMMAND

     Specifies an `AT...' command that will be sent to the modem at the
     *end* of the modem initialization, right before dialing. *Do not
     use ATZ or such here*, since resetting the modem will switch off
     fax mode. Default is `FAX_MODEM_HANDSHAKE'.

   - `modem-type' [-C] TYPE

     Force the modem command set to use. Default is `auto' (auto-detect,
     which may not work on very cheap modems), possible other values are
     `cls2', for "class 2 only" modems, and `c2.0' for "class 2.0"
     faxmodems. Default is `DEFAULT_MODEMTYPE'. *Note runtime-mgetty::.

   - `modem-quirks' BITMASK

     Same as in `mgetty', this can be used to adapt `sendfax' to some
     peculiarities in certain modems. *Note runtime-mgetty::.

   - `reset-after-fail'  COMMAND

     Specifies an `AT...' command that is to be sent to the modem in the
     case of a dialup failure (NO CARRIER, NO DIALTONE).  This could be
     something to reset the modem's ISDN logic (`ATZ!') in case you run
     into communication problems between modem and ISDN PABX.  Should
     only ever be necessary in very special cases.

   - `max-tries' NNN

     Specify the maximum number of tries per page if the receiving end
     reports reception errors. If NNN tries do not suffice to
     successfully transmit a page, `sendfax' will give up or simply go
     on, depending on the setting of `max-tries-continue' (see below).
     If this is set to `0', `sendfax' will ignore retransmission
     requests and simply go on.  Default is `FAX_SEND_MAX_TRIES'.

   - `max-tries-continue' Y|N

     After the maximum number of tries for one page are reached,
     `sendfax' can report an error and abort (`max-tries-continue NO'),
     or go on with the next page (YES).

     For "mission critical" faxes, I'd set it to NO, but since the page
     quality is most often quite good even if reported as "page bad",
     the default is YES.

   - `speed' BAUDRATE

     Set the port speed to use for fax send operations. Usually,
     `38400' is a good choice, but a few dumb modems (for example, some
     based on rockwell chipsets) need `19200' or even `9600'. A few
     modems can go higher, but `sendfax' may not support it, and it may
     not always work.  Default is `FAX_SEND_BAUD'.

   - `switchbd' BAUDRATE

     On some (very few) modems it is necessary to start with baudrate
     "A" and switch to baudrate "B" after sending the `AT+FCLASS=2'
     command. If you specify this, `sendfax' will switch from `speed' to
     `switchbd' right after setting the modem to class 2/2.0. Default is
     `FAX_SEND_SWITCHBD', I'd recommend *not* using it unless you're
     sure that you need it.

   - `open-delay' MSEC

     A few modems respond to raising the DTR line (when opening the
     device) with `OK'.  This can confuse `sendfax', because it will see
     this OK as response to the next command.  In the log file, you can
     see if your modem exhibits this problem if the echo of each `AT'
     command can be seen when waiting for the response to the _next_
     `AT' command.  With `open-delay' you can give a number of
     milliseconds to wait after the device is active until sendfax
     flushes all incoming responses and goes ahead.

     The only modems that need this so far are an ELSA 33.6 and an ELSA
     MicroLink 56k, and delaying for about 1500 ms cured the problem.

   - `ignore-carrier' Y|N

     Some misbehaving modems lower the DCD (carrier detect) line briefly
     between sending multiple pages.  Depending on the operating system
     used, this may cause all subsequent port accesses on this serial
     port to fail.  You'll recognize it if you get a "weird-looking"
     sendfax log file that works fine up to the end of the first page,
     and then aborts with `I/O error' or so.

     In earlier versions, you could achieve this by setting
     `FAX_SEND_IGNORE_CARRIER' in `policy.h', but this has been
     removed.  Use the config file instead.

     Modems where this is known to be necessary include all USR modems
     (Courier and Sportsters), some ZyXEL 1496 EG(+), and some GVC
     models.

     The default is `ignore-carrier yes', as there are just too many
     users out there to read documentation, and it does less harm that
     way.

   - `dial-prefix' COMMAND

     This is the command used for dialing out. Usually this will be
     something simple, as `ATD' or `ATDP', but if you have an unusual
     setup, it could also be something like `ATX0DP0;X4DT' (meaning:
     switch off dial-tone detection, pulse-dial `0', back to command
     mode, switch on dial-tone detection, and go ahead dialing with
     touch tones). The phone number will be sent right after the
     `dial-prefix'. Default is `FAX_DIAL_PREFIX'.

   - `fax-id' [-I] YOUR FAX PHONE

     specifies the "fax station id" used to identify your fax machine
     to the receiving end. Usually this is the telephone number of your
     own fax machine, but if you want to (and if your modem support
     it), you can put up to 20 alphanumeric characters here, e.g.
     `+1-11-222 Fred'. Default is `FAX_STATION_ID'.

     Watch out: the `faxspool' program _only_ uses the _global_
     definition from sendfax' config file, so the fax id it puts on the
     header might not be the same as the one transmitted by sendfax, if
     you use port specific settings for `fax-id' in `sendfax.config'
     (Paul Sands).

   - `poll-dir' [-d] FULL PATH

     This is used to specify a directory where polled faxes (wheather
     maps and such) are to be saved into. Default is the current
     directory.

   - `normal-res' Y|N [-n]

     If set to `yes' or `true' (boolean), `sendfax' won't attempt to
     make a fax connection in "fine resolution" mode. Normally you
     won't need to use that option, since `faxrunq' will set the `-n'
     switch if needed.  Default is `no'

   - `fax-min-speed' SPEED

     Sets the lowest transmission speed that the modem will negotiate
     with the receiving modem. (Not implemented yet).

   - `fax-max-speed' SPEED [-M]

     Sets the maximum transmission speed that the modem will negotiate
     with the fax receiver.  Usually, you don't need this, as decent
     modems will pick the best speed automtically, but sometimes (e.g.
     for the USR Courier series) this doesn't always works, and
     transmission fails with +FHS:25.  If you see that error, you might
     want to try `fax-max-speed 7200'.

   - `verbose' Y|N [-v]

     If set to `yes' or `true', `sendfax' will output progress reports
     on stdout, if set to `no', `sendfax' will only print error and
     warning messages. Default is `no'.

   - `debug' [-x] NN

     controls the amount of information written into the fax log file
     (`FAX_LOG' in `policy.h'). `0' means "totally silent" (not even
     errors are written), `9' is really noisy. I usually use `3' or `4'
     in normal use, and `6' for debugging. Default is `LOG_LEVEL'.

   - `page-header' [-h] FILE

     Yet unused (because of implementation shortcomings in all tested
     modems)


   To show you how it will look like, I have included a sample
`sendfax.config' file below. Three modem lines exist on my system, all
modems have different initialization and flow control commands, and on
one line I have to tell the modem to use pulse dial because the PBX is
too old.

     #
     # sample configuration file for sendfax
     #

     # global settings
     verbose y
     # the modems are attached to the following ports:
     fax-devices tty1a:tty2a:tty4c

     # this is my fax number
     fax-id +49-89-xxxxxx

     # generic defaults
     modem-init ATL3M1
     dial-prefix ATD
     debug 4

     # port specific overrides

     # Zoom 28K8
     port tty1a
       modem-handshake AT&K4

     # MultiTech
     port tty2a
       dial-prefix ATDP
       modem-handshake
     #                ^^^ this means "no extra command to set modem handshake"
       debug 9

     # ZyXEL
     port tty4c
       modem-init ATM1L2
       modem-handshake AT&H3


File: mgetty.info,  Node: voice,  Next: Problems,  Prev: Fax,  Up: Top

4 Voice Operations
******************

This chapter explains how you can use mgetty to implement an answering
machine if you have a modem that understands the voice command set
(i.e. the ZyXEL).

   The first version of these extentions was written by Klaus Weidner.

   Since February 1995 these extentions are now developed and maintained
by Marc Eberhard (Marc.Eberhard@Poseidon.ThPhy.Uni-Duesseldorf.DE).
Since late 1998, Marc Schaefer (schaefer@alphanet.ch) took over vgetty
development. Please see
http://www-internal.alphanet.ch/~schaefer/vgetty.html for vgetty
specific information, patches and releases, and please send email about
the voice features to him, not to me.

   *I have removed the whole chapter from the documentation for now, as
the voice stuff has changed too much, but the docs were not updated
accordingly. Please see the programs and examples in the `voice'
subdirectory for ideas how to get it going. Configuration is explained
in `voice.conf'*.

   The `voice' subtree is *NOT* included in the official release 1.0,
because of the lack of documentation, and because Marc thinks it's not
stable enough yet.  It _is_ included in the 0.99 and 1.1 beta
development trees, so if you want to play with it, get one of those
version. *BUT* keep in mind what "beta" means: lacking documentation,
problems, crashes, whatever.


File: mgetty.info,  Node: Problems,  Next: Thanks,  Prev: voice,  Up: Top

5 Common problems and solutions (TROUBLESHOOTING)
*************************************************

This chapter tries to describe some known problems that can occur when
installing or using this package. Don't worry, most of these have been
solved.

* Menu:

* Modems::          Modems
* Systems::         Operating Systems
* General::         General problems
* logfiles::        Sample Log files
* ftp::             Where to find the programs mentioned (FTP)
* get-uucp::        How to get the software via UUCP


File: mgetty.info,  Node: Modems,  Next: Systems,  Prev: Problems,  Up: Problems

5.1 Modems
==========

This section describes problems that can occur when using various types
of modems. Unfortunately, the class 2 fax implementations vary quite a
bit between different manufacturers.

   Many of the instructions for certain modem types below still refer to
changing `#define's in `policy.h' instead of listing the appropriate
`mgetty.config'/`sendfax.config' lines, mainly because I haven't had
the time to figure it out myself and didn't get enough feedback from
config file users yet.

* Menu:

* Common::          Problems common to many modem types
* Zyxel::           ZyXEL U1496 modem series
* TelelinkIMS08::   Telelink IMS 08 Faxline + Modems
* Rockwell::        Rockwell-based modems, e.g. Supra
* Zoom-vfast::      Zoom VFP/VFX 24K FaxModem (V.FAST 24,000 Modem)
* Best14496EC::     Best 14496 EC Faxmodem
* GVC::             GVC FM-144Vbis+/1 (Rockwell-Based)
* creatix::         CREATIX modems (Rockwell-Based)
* Telekom::         German Telekom approved GVC modems
* Dallas::          Dallas Fax 14.4
* Everex::          Everex
* Exar::            Exar 9624 fax modem
* Tornado::         Tornado / Lightspeed modems
* Zoltrix::         Zoltrix Platinum Series 14.4 (Rockwell-Based)
* MultiTech::       MultiTech modems
* ELSA::            ELSA analog/ISDN faxmodems
* USR::             US Robotics Courier/Sportster Data/Faxmodems
* Elink-ISDN::      Elink ISDN Terminal Adaptors (``ISDN Modems'')
* i4l::             ISDN 4 Linux support
* i4l-capi::        ISDN 4 Linux with CAPI (capi4linux)
* Class 1::         Class 1 Faxmodems


File: mgetty.info,  Node: Common,  Next: Zyxel,  Prev: Modems,  Up: Modems

5.1.1 Problems common to many modem types
-----------------------------------------

   * Disable auto-answer in the modem (`ATS0=0'), because it will
     interfere with the manual answer done by `mgetty'. If you _have_
     to use auto-answer, set the `mgetty' ring-counter (`-n <i>') high
     enough that `mgetty' will never try to answer the phone manually.

   * Make sure that your modem is set to return _verbose result codes_,
     that is, set `ATV1'. Otherwise, the modem won't return `CONNECT'
     or `RING' but `1' or `2' as result code, and mgetty definitely
     doesn't understand that. By default, `mgetty' sets `ATV1'
     automatically, but if you change the init sequence, watch out for
     this.

   * Make sure that your modem is set to the proper dialing type
     (`ATT&W' for touch-tone, `ATP&W' for pulse dialing) -- `sendfax'
     uses `ATD...' to dial out, assuming that the modem knows which
     dialing method to use. Alternatively, set `FAX_DIAL_PREFIX' in
     `policy.h' or `dial-prefix' in `sendfax.config' accordingly.

   * If the default modem initialization string in `policy.h', which is
     quite generic, doesn't work for your modem, you can either change
     it according to your needs, or store all settings in the
     non-volatile RAM (NVRAM) inside the modem and change the
     initialization strings to plain `ATZ' (modem reset).

     These settings ought to work with most modems:

     `ATS0=0': do not auto-answer, `E1': echo on, `Q0': send modem
     responses, `&D3': reset on DTR->low.

     The following, for example, are ZyXEL specific things:

     `&H3': set handshake to RTS+CTS, `&N0': "multi-auto" connect,
     accept all known protocols, `&K4': enable v42bis/mnp5 compression.

     Naturally, you can use any init string you want (but the modem has
     to return OK) -- check with your modem manual.

   * On USR and some ELSA Modems, it has occasionally been reported
     that the initialization phase runs through fine, but incoming
     `RING' messages are not recognized, and mgetty complains about
     `junk on the line'.  In all those cases, it were baud rate
     problems. The modem was initialized with an init-sequence of `""
     ATZ OK' only. Problem with this is, after ATZ, the modem changes
     to the DTE baud rate that the last AT&W command was sent with. If
     that baud rate differs from the `mgetty' port speed, a RING won't
     be detected.  Fix is easy: send another `AT' command after the
     `ATZ'. For example, make the init sequence `"" ATZ OK AT OK'. The
     second `AT' command will set the modem back to the mgetty port
     speed.

   * Some modems do not like the `+FDCC=1,5,...' command.

     In the latest version, mgetty and sendfax will automatically
     detect if the modem isn't able to do 14400 bps for faxing and will
     use 9600 bps -- `+FDCC=1,3,...' -- instead. So don't worry about
     the error message.

   * Sometimes mgetty cannot initialize the modem, it times out waiting
     for the first `OK'. (USR Sportsters are known to hit this).

     I assume that the problem is the DTR-induced modem reset before
     sending the first `+++ATH' to the modem.  I know that some modems
     need quite a lot time after a reset, so this should go away if you
     add more delays before sending the first string to the modem:

     In `conf_mg.c' (line 38 or so) change

          char *def_init_chat_seq[] =
                     { "", "\\d\\d\\d+++\\d\\d\\d\r\\dATQ0V1H0", "OK",

     to

          char *def_init_chat_seq[] =
                     { "", "\\d\\d\\d\\d\\d\\d+++\\d\\d\\d\r\\dATQ0V1H0", "OK",
                             ^^^^^^^^^ additional delays here

     Or, if you don't want to modify the code, just set the `init-chat'
     sequence in `mgetty.config' accordingly.

     Alternatively, you can just switch off the toggling of DTR (since
     the HUPCL flag is set, it should work as well) by setting
     `toggle-dtr no' in `mgetty.config'.

   * Some operating systems send their commands too fast for some
     modems (Linux is known to do this). In that case it may be
     necessary to increase the delay times for `DO_CHAT_SEND_DELAY' and
     `FAX_COMMAND_DELAY' in `policy.h'.

   * Some Modems toggle DCD between pages, possibly correlated to the
     presence of the "high speed" page transmission carrier. `sendfax'
     normally runs carrier-sensitive, and will then get a lot error
     messages in the `read' and `write' calls, logging them as `I/O
     Error' or something similar when sending the first or second page.
     To work around this, set `ignore-carrier true' in `sendfax.config'.

     If you run into this problem, `sendfax' will complain about `Error
     +FHNG:-5 (Unexpected hangup / read() error / write() error)' and
     abort.

   * Some modems do not understand `ATH0', responding with `ERROR' to
     that. Just modify the `init-chat' setting in `mgetty.config' to
     send `ATH' instead of `ATH0'. This will fix it.

   * Faxing to some modems works very well, faxing to "normal" fax
     machines fails all the time.

     In most cases, this error is caused by badly created G3 files. If
     you use the old `pbm2g3' program, or an old copy of `hp2hig3', it
     will cause bad G3 files.

     Recently, a new problem appeared for postscript files created by
     certain programs that insist on setting their ideas of the page
     size (some versions of WinWord, FrameMaker, and dvipsk). If used
     together with ghostscript 3.*, the resulting G3 file's width isn't
     correct. For a fix, try creating the postscript file with a
     different program, use a newer version of ghostscript, or an older
     one (2.62 is fine). Quite often it helps to add `-sPAPERSIZE=a4'
     to Ghostscript's command line (in `faxspool').

     With a `mgetty' version later than June 1996, the `g3cat' program
     should take care of this problem, fixing the line width
     on-the-fly. It will print a warning, to tell you about the problem,
     though. So if you get this warning, faxing should work, but you'd
     better check all your programs anyway.

   * Some other Modems cannot (or not properly) distinguish between
     calling faxes and calling modems.

     Some of them just refuse to answer both, only recognizing one and
     failing on the other (NO CARRIER) -- in that case, there's nothing
     you can do to make it receive both (except making the manufacturer
     fix it). What you can do is to force it to receive always fax or
     always data (what is more important for you). Data-Only can be set
     by the `data-only' keyword in the configuration file, and Fax-Only
     with the `fax-only' keyword.

     In some cases, those problems may be caused by the modem
     forgetting the `AT+FAA=1' command if it receives any other command
     after it. To fix it, it may help to change the "answer chat
     command" in the config file to

          answer-chat "" AT+FAA=1;A CONNECT \c \r

     if this helps for your modem, please tell me so, and I'll include
     it into the documentation.

     Some other modems can distinguish the different call types _most of
     the time_, but some 2400 bps modems mysteriously fail. That may be
     caused by some - strange - modems sending a certain tone when
     _calling_ the other side, and the receiving end mistaking that for
     the fax calling tone.  Arne Marschall said about that: "...Or try
     calling your modem with your phone and whistle. If it says "+fcon"
     it is one one those which can't deal with modems using a calling
     tone" - try it.

     Another, quite simplistic approach of some modem manufacturers is
     that they distinguish Fax by waiting until the time specified in
     register `S7' (time to carrier) runs out, and then switching from
     data to fax carrier. That normally works quite well - if the other
     side is patient enough to wait that long .... For example, if the
     modem switches to fax after 60 seconds have passed, and the caller
     has a timeout of 50 seconds, it will definitely fail. If in doubt,
     try setting `ATS7=30' (but only if all else fails - and don't ask
     _me_ why it doesn't work...)

   * Except if you feel sure that your modem needs less, do not try to
     send or receive faxes with a port speed of less than 19200 bps.
     Since fax transmission is synchronous (no start and stop bit!),
     you need at least 12000 bps on the Computer-Modem line to transmit
     9600 bps on the line.

   * For some modems, incoming faxes are detected properly, but mgetty
     times out about two minutes later in `fax_wait_for(OK)'. Most
     likely, the `switchbd' (`mgetty.config') speed is set wrongly.  A
     number of cheap modems (e.g. Rockwell-Chip based ones) step to
     19200 bps upon fax reception, and setting this option to `19200'
     will tell mgetty about it. Better modems have no need for that, so
     if you have defined it and your modem does *not* change bit rates,
     it won't work either.

     If you have this problem, your log file for an incoming fax call
     will look like this:

          09/21 09:55:48 yS1  waiting for ``RING''
          09/21 09:55:48 yS1  got: [0d][0a]RING ** found **
          09/21 09:55:48 yS1  send: ATA[0d]
          09/21 09:55:48 yS1  waiting for ``CONNECT''
          09/21 09:55:48 yS1  got: [0d][0a]ATA[0d][0d][0a]FAX
          09/21 09:55:50 yS1  found action string: ``FAX''
          09/21 09:55:50 yS1  start fax receiver...
          09/21 09:55:50 yS1  fax receiver: entry
          09/21 09:55:50 yS1  fax_wait_for(OK)
          09/21 09:55:56 yS1  fax_wait_for: string '+FCON'
          09/21 09:57:50 yS1  Warning: got alarm signal!
          09/21 09:57:50 yS1  fax_read_byte: read returned -1: Interrupted system call
          09/21 09:57:50 yS1  fax_get_line: cannot read byte, return: Interrupted system call

   * For a couple of modems, you can find initialization and setup
     hints in the file `doc/modems.db'. Just browse through it, maybe
     you'll find something helpful. (You're welcome to provide entries
     for modems not yet in the list).

   * Sometimes, very weird things happen upon login (that is, long after
     `mgetty' has done its work), for example, /bin/login blocks
     infinitely, the caller is thrown out immediately again, or the
     shell won't notice a logout, etc.

     Quite often, this is caused by a modem not setting the data
     carrier detect (DCD) line properly (properly meaning here
     "reflecting the actual line conditions"). On most modems this is
     done with the `AT&C1' command.

     Another possibility are too long or otherwise broken modem cables
     that corrupt the signals, and introduce noise on the modem control
     lines. Flat cables are famous for this, use round, shielded modem
     cables, no longer than necessary.

   * `mgetty' will complain loudly if you switch off your modem.

     Well, what should I say, this is a feature :-) - I think that
     mgetty should detect and complain if a modem is not working, and
     if you switch it off, it is most definitely not working.

     For most modems, there is an easy way out.  `mgetty' can query the
     modem's DSR line at startup, and wait until that line comes
     active.  For that to work, you need to set DSR to "always on" with
     `AT&S0&W' (entered from a terminal program), and then switch on
     `need-dsr yes' in `mgetty.config'.  Check the log file (with
     `debug 6') to see whether it's working.  It won't work for old
     unix systems where you can't query the state of the serial port
     control lines (DSR, DCD, etc.).

     For modems or unix systems that have problems with DSR, there's
     another approach: You just create a file, `/etc/nomodem.ttyS1', or
     however you want to name it, when you intend to switch off your
     modem.  Instead of running `mgetty' from `/etc/inittab', you run a
     "wrapper" script that will wait until the nomodem file disappears,
     and then starts `mgetty'. That way, you can just prevent `mgetty'
     from starting when you don't want it to.

     The wrapper is easy:

          #!/bin/sh
          #
          while test -f /etc/nologin.ttyS1
          do
             sleep 60
             done
          exec /usr/local/sbin/mgetty ttyS1

   * I have been asked about "superfine" fax mode recently (using
     392/408 dpi instead the usual 198/204 dpi).  It is not yet
     implemented.  It would not be not overly hard, but you need a
     modem that supports it - no class 2 modems that I know of support
     it, and only very few 2.0/2.1 modems (MultiTech).  So it hasn't
     been done yet.

   * Similar to the last bullet, V34 fax (using transfer speeds up to
     28.800 bps) isn't fully implemented yet.  My modems do not support
     it, and nobody has asked for it yet.  It should be really easy,
     though.



File: mgetty.info,  Node: Zyxel,  Next: TelelinkIMS08,  Prev: Common,  Up: Modems

5.1.2 ZyXEL
-----------

First of all, yes, ZyXELs tend to somewhat non-deterministic behaviour -
most modems work perfectly with `mgetty+sendfax', a few don't, and I do
not always find out what's wrong.

   If it works first, and then suddenly stops working, it does quite
often help do to a *full* modem reset, that is, switch it off, press the
DATA/VOICE key, switch it on again and hold the key for about 20
Seconds.  (That's for the 1496E and E+, for other models, it works
differently, check you manual). That cured the problems in many cases.

   The same holds true after a firmware change: always do a full modem
reset in case you change the ROM version!

   Do not use non-plus ZyXELs (the "slower" ones) for faxing with DTE
speeds above 38400 bps, I got a report that it won't work.

   Do not use the `S18' register, set it to 0. Its purpose is for dumb
`getty' programs where the modem has to change its baud rate back to a
certain value if some other program has modified it. Since `mgetty'
will reinitialize the modem anyway if another program has dialed out,
the `S18' register cannot improve anything, it can only harm (e.g., if
it is set to `3', the modem will send any `RING' with 19200 bps --
imagine what happens if `mgetty' sets the port to 38400 ...)

   If you want to use Caller ID (and have subscribed to it), add
S40.2=1 to the modem initialization string [For the ZyXEL 2864, this
might be S84.4=0, but check with your modem manual!].

   *Warning:* If you use a very old ZyXEL and try to send some complex
graphics (the "tiger.ps" example file in the GhostScript package is
known to produce this), it may lock up. This is because the old ZyXEL
firmware had _lots_ of bugs concerning hardware flow control--sometimes
the ZyXEL just forgot to raise CTS when it can accept data again. The
symptoms are that the transmission hangs, no modem LEDs are flashing
any more, the logfile won't grow any more and the receiving machines
hangs up after printing a partial page.

   This bug has been fixed in ROM release 6.01, so you should consider
upgrading your eproms if you run into this. With ROM release 6.01 and
6.11a, it works correctly (a hundred-odd faxes sent without problems).

   Rom releases I've never been able to make `sendfax' work reliably are
6.00 and 6.10 (6.10a works), and various 5.0x releases.

   Fax polling (both server and client side) is broken in ROM 6.11a.

   The very latest ROM releases, 6.12, 6.13 and 6.15, work perfectly in
every possible aspect. I tried fax sending, receiving, polling, data
calls, ... - and everything simply _works_!

   The latest ZyXEL roms can normally be found on ftp.zyxel.com, in
`/pub/other/zyxel/r*'.

   Some models, seemingly only the `EG+' (german telekom approved),
toggle the DCD line during the pre-page handshake, thus causing
`sendfax' to abort (with a "I/O error" during read/write operations).
You can work around this by defining `ignore-carrier true' in
`sendfax.config'.

   ZyXEL modems can do security callback (`AT*Gi' with `i' > 0).  With
ROM releases up to 6.11a, this doesn't interact very well with mgetty.
If you want to use it anyway, send me a note and I'll describe what to
change (but be warned, mgetty operation will become somewhat unreliable
by those changes!). With 6.12, it works very good.

   Oh, one additional note: ZyXELs can do voice recording and playback.
Klaus Weidner and Marc Eberhard have written voice handling tools, to
turn your modem into a sophisticated answering machine. Yo can finde
this tools in the `voice' subdirectory. (NOTE: In version 1.0, I
haven't included the stuff, because the docs are heavily lacking and
Marc thinks it's not ready yet. Get 0.99 or 1.1-betas to play with
voice).

   Josef Wolf (jw@raven.inka.de) has added some comments about the ZyXEL
Eproms (I don't know whether it's true or not, ask him or
support@zyxel.com):

   Most EPROMs require /PGM and Vpp to be Vcc while in ROM-Mode. On
ZyXELs these two pins are removed in the socket so the pins are
_floating_. This treatment is *out of spec* for _any_ EPROM. The
TI-Types originally used by ZyXEL seem to tolarate this treatment. But
most other EPROMS won't work properly. There are two solutions to this
problem:

   1.) use the types which zyxel used. (could be troublesome to find
some)

   2.) take two sockets, solder jumpers between pins 1, 31 and 32
(these are     /PGM, Vpp and Vcc) and place them into the original
sockets before     inserting the EPROMs.

   *NEWS:* ZyXEL has a new modem line out in the market, the _ZyXEL
COMET 336_ modem.  This is a fairly standard Rockwell-based junk modem.
It can't do class 2 or class 2.0 fax.  Don't buy it.


File: mgetty.info,  Node: TelelinkIMS08,  Next: Rockwell,  Prev: Zyxel,  Up: Modems

5.1.3 Telelink IMS 08 Faxline+ Modems
-------------------------------------

Thanks to friendly support by MVS, Germany, I got a Telelink IMS 08
modem for testing and was able to adapt `mgetty' accordingly.

   The modems factory defaults are very good, so it's sufficient for
`mgetty' operations to set `init-chat' (in `mgetty.config') to ATQ0V1E0
OK AT&F2S0=0&D3X6&K3 OK, and `switchbd' to 19200 (yep, it switches baud
rate.  Stupid, but true). After that, receiving fax + data calls works
fine.

   Fax sending is not that trivial. Basically, it works after setting
`modem-handshake' to `AT&K3'. `FAX_SEND_FLOW' (in `policy.h') can be
anything that the host machine supports (because the modem does both
Xon/Xoff and RTS/CTS handshake simultaneously).

   Unfortunately, a few problems remain:

   - faxing multi-page faxes to ZyXELs with ROM release 6.11a doesn't
work (fails on the receiving end with +FHNG:100 and on the sending side
with +FHNG:50).

   - faxing to some paper fax machines fails completely, for others,
"only" complex graphics (like the Ghostscript-"tiger.ps") fail. This
one can be partially cured by adding lots of padding zeroes into the
fax data (`g3cat -p 24') - but that's unelegant, not complying to class
2 specs, and not supported (besides, it still doesn't work all the
time). Maybe later versions of `sendfax' will do the padding
automatically.

   I recommend against using this modem with sendfax. In addition to the
technical problems, their customer support (at least, that of the german
distributor MVS) is basically non-existant. (I wrote them four times
describing my problems with the modem, and never got an answer).


File: mgetty.info,  Node: Rockwell,  Next: Zoom-vfast,  Prev: TelelinkIMS08,  Up: Modems

5.1.4 Rockwell-based modems, e.g. Supra
---------------------------------------

As far as I know, sending or receiving are no problem (although you
have to use 19200 baud when in class 2 faxmode - set `speed' to `19200'
in `sendfax.config', and set `switchbd' to `19200' in `mgetty.config'.
Remember to change the modem initialization strings to the proper
values for your modem, that is, ATQ0V1E0 OK AT&K3S0=0 OK.

   Especially for the `SupraFax' modem, I've been told that you have to
set `modem-handshake' to `AT&K3' and initialize the modem with
`AT&S0&D2&K3'. Since the modem does not like being reset with DTR->low
(do *not* use `&D3'!), an `ATZ' in the first initizalization string in
`mgetty.c', to reset the modem into a known state, is a good idea, too.

   (Thanks to Christof Junge, chris@cj.in-berlin.de, for trying out
several weeks until everything worked!)

   Some other SupraFAX Rom releases seem to forget that they are set to
use RTS/CTS handshake if a `+FCLASS=0' is sent to them. I think it
should help to store the `AT&K3' into NVRAM, but maybe you have to patch
`mgetty.c'. See `contrib/readme.supra' for details.

   Fax polling does not work because the Rockwell chipset does not
support it.

   *NEWS:* Most recent Rockwell 33.600 modems do not support any decent
fax operation anymore - they added "simultaneous Voice over Data" (SVD)
to their modem firmware, and because the Eproms are not large enough,
they threw out their class 2 firmware.  Don't buy such a modem, it
won't work properly with `mgetty+sendfax'.

   If you buy a Rockwell-based modem (they are usually quite cheap),
make sure that you get one that can do class 2 or (better) class 2.0.
Even if it's written on the box, some recent models just can't do it!

   Together with `vgetty', many Rockwell modems can distinguish between
different types of incoming "RING" tones (usually called "distinguished
RING" by the local Telco).  Use the command `AT#SDR=n' (n between 0 and
7) to enable this feature.  If in doubt, check with your modem manual
whether your modem can do this at all.


File: mgetty.info,  Node: Zoom-vfast,  Next: Best14496EC,  Prev: Rockwell,  Up: Modems

5.1.5 Zoom VFP/VFX 24K FaxModem (V.FAST modem, 24,000 bps)
----------------------------------------------------------

For the Zoom V.FAST 24,000 modem, you should change `init-chat' to
`ATE1Q0V1 OK AT&FS0=0&C1&D2W1 OK' (see the manual for the meaning of
the commands). After that, everything should work. (I got very euphoric
reports).

   My own experience with my Zoom VFX 28.800 is also quite good, but it
doesn't seem to like automatic fax/data distinction too much, that is,
some data calls are "recognized" as fax and fail miserably. Dunno how
to fix it, I run my Zoom as data-only.

   Fax polling doesn't work.


File: mgetty.info,  Node: Best14496EC,  Next: GVC,  Prev: Zoom-vfast,  Up: Modems

5.1.6 Best 14496 EC fax modem
-----------------------------

Works quite well. Use `FLOW_HARD' for all flow control settings (in
`policy.h', use 19200 bps for sending and receiving. Set `modem-init'
to `ATE1Q0V1 OK ATS7=60&D3\\Q3%C1\\N7 OK' (`mgetty.config'), and
`modem-handshake' to `AT\\Q3&S0' (`sendfax.config').

   After that it should work. Kudos to Sami Koskinen (tossu@krk.fi).


File: mgetty.info,  Node: GVC,  Next: creatix,  Prev: Best14496EC,  Up: Modems

5.1.7 GVC FM-144Vbis+/1 (Rockwell-based)
----------------------------------------

Basically, the modem is similar to the SupraFax modem.

   Change `speed' in `mgetty.config' and `sendfax.config' to `19200'
and set `modem-handshake' to AT&K4.

   Further, if your model toggles DCD betwen fax pages (`sendfax' fails
mysteriously between pages), `ignore-carrier true' in `sendfax.config'.

   After that, it should work.

   Note: If your modem doesn't properly distinguish incoming fax from
data calls (i.e., a 2400 bps caller is repeatedly "identified" as fax
caller), upgrade your firmware. I've been told (thanks to John Watson,
watson%carssdf@rutgers.edu) that a new firmware release, *v1.69* exists
that will fix those problems.


File: mgetty.info,  Node: creatix,  Next: Telekom,  Prev: GVC,  Up: Modems

5.1.8 CREATIX Modem (Rockwell-Based)
------------------------------------

For the new CREATIX modem, use the following settings in `mgetty.config'
(thanks to Jens Hektor, jens@physiology.rwth-aachen.de):

     speed 38400
     init-chat "" ATE1Q0V1 OK ATS0=0&D3&K3

   and `modem-handshake' AT&K3 in `sendfax.config'.

   The modem has a voice mode, too, and it should work with `vgetty' by
now. As the docs for vgetty are out-of-date, I don't really know how to
get it to work, though.


File: mgetty.info,  Node: Telekom,  Next: Dallas,  Prev: creatix,  Up: Modems

5.1.9 German Telekom approved GVC modems
----------------------------------------

(GM-144VBIS+  RC9696/14 (?))

   This modem does _not(!)_ use Xon/Xoff flow control. Further, the
default modem profile sets `&S1', which makes the modem disable DSR all
the time. On systems using the FAS serial driver, this will _disable
CTS flow control_!

   So, #define `FAX_MODEM_HANDSHAKE "AT\\Q3&S0"' in `policy.h', do not
define `FLOW_SOFT' for flow control, and fax sending should work. (It
does for me!)  Changing `FAX_SEND_BAUD' to `B19200' is not necessary,
it works with `B38400'.

   Fax receiving... I did not fully test it. It's somewhat difficult
since that modem insists on using auto-answer, but it should be
possible to let it auto-answer if you set mgetty's ring counter high
enough. Or, you can trick the modem, by changing mgetty's answer
command (`ATA') into `ATS0=1' - upon the next RING, the modem will
"auto-answer".


File: mgetty.info,  Node: Dallas,  Next: Everex,  Prev: Telekom,  Up: Modems

5.1.10 Dallas Fax 14.4
----------------------

Change `FAX_SEND_BAUD' and `DEFAULT_PORTSPEED' to `B19200', change all
occurances of `AT&H3' to `AT&K5', remove `AT&N0' and `&K4' in
`policy.h'.


File: mgetty.info,  Node: Everex,  Next: Exar,  Prev: Dallas,  Up: Modems

5.1.11 Everex
-------------

All I programmed is strictly to everex specs, thus, it should work.
Most likely, some fiddling with the initialization strings is necessary.
(If you have an Everex modem, please report to me what you did change).


File: mgetty.info,  Node: Exar,  Next: Tornado,  Prev: Everex,  Up: Modems

5.1.12 Exar 9624 fax modem
--------------------------

This modem needs two stop bits (when sending), so you have to add
`CSTOPB' to `tio.c_cflag = ...' in `tio.c' / `tio_mode_sane()'.

   Also, use `#define FAX_SEND_BAUD B19200' and, for fax reception,
`#define DEFAULT_PORTSPEED B19200'.

   Further, the modem is a little bit timing critical - please insert
`delay(500)' calls at the end of `fax_open_device()' (`sendfax.c', line
122) and before sending the page punctuation (`fax_command("+FET=...")'
in `sendfax.c', `main()', around line 540).

   Also, for at least one Exar 9624 (built into a Compaq notebook),
it's been necessary to add two delays (`\\d\\d') before the
`AT+FCLASS=0' initialization string in `mgetty.c'.


File: mgetty.info,  Node: Tornado,  Next: Zoltrix,  Prev: Exar,  Up: Modems

5.1.13 Tornado / Lightspeed modems
----------------------------------

Here is a suggested setting for the default profile for these modems.
*Note Common::.

   For Lightspeed store profile:
     at&f
     at&c1
     at&d3
     ats0=0
     at%c2
     atw1
     at&w

   and for tornado store profile:

     at&f
     at&d3
     ats0=0
     at&w

   Then just initialize the modem with `init-chat' set to `"" ATZ OK'.


File: mgetty.info,  Node: Zoltrix,  Next: MultiTech,  Prev: Tornado,  Up: Modems

5.1.14 Zoltrix Platinum Series 14.4
-----------------------------------

This modem is also Rockwell-based, so don't expect anything unusual...
- it works quite well, both fax sending and fax/data answering. You
should use the following settings in `policy.h' (suggested by
las@io.org, Laszlo Herczeg)

     #define DATA_FLOW	FLOW_HARD
     #define FAXREC_FLOW	FLOW_SOFT
     #define FAXSEND_FLOW	FLOW_SOFT
     #define FAX_SEND_BAUD B38400
     #define FAX_MODEM_HANDSHAKE "AT&K3"
     #define MODEM_INIT_STRING	"ATS0=0V1Q0&D3&K3%C1W1"

   In some circumstances, sending of *large* graphics files (the
well-known `tiger.ps') may fail.


File: mgetty.info,  Node: MultiTech,  Next: ELSA,  Prev: Zoltrix,  Up: Modems

5.1.15 MultiTech modems (MT1432BG and MT2834BG)
-----------------------------------------------

First of all, I want to thank MultiTech Munich for their support
(borrowing me two test modems w/o charge).

   Second, I can only strongly recommend these modems, they are *great*
(but expensive). Got it, unpacked it, switched it on, set mgetty's init
string (`MODEM_INIT') to `ATS0=0&S1' - and everything simply worked.
Flawlessly. (Warning: usually I recommend `AT&S0' to force the DSR line
high - needed, because otherwise some O/Ses won't do hardware flow
control - but that doesn't seem to work on my model. AT&S1 means that
H/W flow control only works when a carrier is present, but then, who
needs flow control in command mode?)

   The modems do very reliably distinguish incoming fax and data calls,
and outgoing fax works also very good (unfortunately, it's limited to
9600 bps fax rate, but that's no big problem).

   The only problem I've seen is that those modem do the fax bit order
on reception *right* (everybody else does it wrong, to be compatible
with Rockwell, who botched it in the first place). Thus, `g32pbm' won't
be able to decode the data, unless you call it as `g32pbm -r'.  (You
can see if the bit order is wrong if g32pbm complains in every single
line). I'll work something out for one of the next releases to work
around this (MODEM-QUIRKS 02).

   BUT: There seems to be a way to tell the modem to behave like a
Rockwell one and use the "wrong" byte order. Carlos Fonseca found the
following text on ftp.multitech.com:

     Function          Command       Description

     PROCESS           +FRBOR        Maintaining compatibility with
     DATA IN                         Rockwell Class 2 chip set for fax data
     DIRECT OR                       reception .
     REVERSE ORDER                   FRBOR=0 - Process received fax data in
                                     direct order.
                                     FRBOR=1 - Process received fax data in
                                     reverse order.

   so, with AT+FRBOR=1 added to the modem initialization string, it
should be possible to get fax reception on the MultiTechs going without
tricks.

   Glenn Thobe suggested the following definitions for `policy.h' (which
mostly are factory defaults anyway, but it wouldn't harm to set them)

     #define MODEM_INIT_STRING	"ATS0=0Q0&D3&E1&E4&E13&E15"
     #define FAX_MODEM_HANDSHAKE "AT&E4"

   My `mgetty.config' for those modems looks like this (everything not
mentioned is set to the defaults I ship in `policy.h').

     # MultiTech MT1432BG
     port <whatever1>
       init-chat "" \d\d\d+++\d\d\dATE0E1V1H0 OK ATL0M0S0=0 OK
       modem-type cls2

     # MultiTech MT2834BG
     port <whatever2>
       init-chat "" \d\d\d+++\d\d\dATH0&F OK ATX4&D3 OK ATQ0L0M0S0=0 OK
       modem-type cls2

   Some of the newer 56k-capable MultiTech modems have voice
functionality, but some firmware versions are very much broken.  Others
seem to work more or less.  So make sure you can return your modem to
the dealer if it doesn't work - and if the dealer isn't willing to do
this, get a different modem.  Russell King told me that the firmware
version 0316D should be working ok, but I got some negative reports as
well. Hmmm.

   *News* The most recent series of MultiTech modems (MT5634ZBA-V92
external, or MT5634ZPX-PCI-V92 / ISI5634PCI internal), based on the
Lucent/Agere Venus chipset, seem to be really good for fax, data and
voice support.  Older firmware releases had bugs in the voice area, but
if you use the most recent firmware version, they should be fine.  For
vgetty, you might need to set "forceV253 true" and "rec_compression 6"
in `voice.conf'  (Contributed by Lee Howard, <faxguy@howardsilvan.com>
- thanks).


File: mgetty.info,  Node: ELSA,  Next: USR,  Prev: MultiTech,  Up: Modems

5.1.16 ELSA voice/fax modems
----------------------------

ELSA makes a nice series of Data/Fax/Voice products, both for POTS
lines and for ISDN.  In general, all of them are supported fairly well
by `mgetty+sendfax' (fax works, fax polling works(!), voice works), but
here are a couple of notes for different products:

   * MicroLink 56k/56k pro - standard analogue voice/fax/data modem.
     Pretty good for about everything, but make sure you use the latest
     firmware version (1.58), as earlier versions have bugs switching
     between voice and fax mode.

   * MicroLink Office - in addition to being a nice modem, this thing
     can do fax reception and answering machine functionality in
     "standalone mode", without a computer.  Received voice calls and
     faxes can be downloaded via X-Modem to the computer.  I'm working
     on a nice GUI application to ease using the standalone mode.  The
     ML Office seems to be the only non-ISDN ELSA modem that can do
     Caller ID (CLIP).

   * MicroLink TL/V.34 - this is an ISDN terminal adaptor that can also
     do V.34 modem calls and fax.  Works nicely.

   * TanGo - this an ISDN only terminal adaptor.  Works, but it's pretty
     boring stuff.

   * MicroLink 28.8/33.6 TQV - this is the old voice/fax/modem series.
     Works, but uses a different command to got to hardware flow
     control mode (`AT\Q3' instead of `AT+IFC=2,2') so you'll see some
     errors in the voice log files.  Don't worry about that.

   If you have any problems with ELSA modems and mgetty concerning
fax/voice support, report them to me first, and let me report them to
ELSA - I'm actively working together with them to iron out bugs, and
it's easier if all the reports come from only one contact person (me).


File: mgetty.info,  Node: USR,  Next: Elink-ISDN,  Prev: ELSA,  Up: Modems

5.1.17 US Robotics (now 3com) Courier/Sportster Fax/Data modems
---------------------------------------------------------------

There are a number of major lines of 3com/US Robotics modems:

   * USR Courier V.34/V.everything - those are quite expensive, but
     really, really good modems.  I think those are the best
     V.34/X.2/V.90 modems around, and they are also very good for class
     2.0 faxing.   But make sure that you use a recent firmware, as
     older versions had very bad (and stooopid) bugs in the fax
     department.  You can find out the firmware version with the `ATI7'
     modem command.  The `Supervisor rev' version listed should be at
     least `6.5.3', better `7.1.8' (this is the `X.2 upgrade').

     Fax polling still doesn't work, and if you send faxes to a modem
     that can only accept fax with 7200 bps, it will fail with
     `+FHS:25' unless you specify `sendfax -M 7200'.

     The Courier series does not have voice features.

   * USR I-Modem - this is an ISDN Terminal Adaptor with built in
     V.34/fax mode ("ISDN Modem").  Nice product.  Works.  The same
     stuff said for the Courier V.34/V.everything is true for the
     I-Modem.

   * older USR Courier modems - older series without flash ROM, and
     possibly not upgradable to V.34/X.2 at all, might give problems.
     Fax was added fairly late, and the first fax-capable releases are
     very buggy.  If you have such a modem, and `ATI7' does not list
     `V34' in the `Options' line, you might try setting `modem-quirks
     0x20' in `mgetty.config'.  Maybe it helps.  But don't expect too
     much.

   * USR Sportster series - the "Sportster" is actually a range of many
     different low-end modems.  Most of them can do voice stuff, some of
     them have flash ROM to be upgraded to newer firmware.  For data,
     this modem is quite good.  For fax, it might work, and it might
     not - I have received a very high number of "it doesn't work at
     all" reports, and also a number of "it works very well for me"
     reports.  If you plan to buy one, make sure you can return it if
     it doesn't work.  (See below for some specific issues and
     workarounds).

   * Internal PC card - I haven't been able to find out yet whether that
     is a "Sportster" or a "Courier", but it seems to be a Sportster,
     with all its negative habits.

   Some older USR firmware versions had severe bugs when doing RTS/CTS
(that is, hardware) flow control. Occasionally, a byte got lost, and
sometimes this confuses the modem enough to abort transmission with the
error message
     Transmission error: +FHNG:44 (Unrecognized Transparent data command)
   Sam Leffler recommends using Xon/Xoff flow control for both fax
sending and fax receiving (`#define FAX_SEND_FLOW FLOW_SOFT' and
`#define FAX_REC_FLOW FLOW_SOFT' in `policy.h').

   Some day in the future, I'll make those "quirks" configurable from
the config file, but until then, you'll have to live with recompiling.
Sorry.  (Upgrade your firmware!).

   Fax polling with the USRs is _not_ working, even though the modem
claims so. It will work half-way through, but fail miserably later.

   When sending faxes with an USR faxmodem, set `ignore-carrier yes' in
`sendfax.config'.  Otherwise it will fail after the first page with a
read error and error code -5.  (But that is default anyway, if you use
mgetty 1.1.16 and up).

   For some fax receivers, a problem remains: the USR modems do not want
to negotiate 7200 bps transmission speed.  If the receiving modem won't
accept 9600 bps, transmission will fail after sending three DCS frames,
with the error code +FHS:25.  In that case, try setting `fax-max-speed
7200' in `sendfax.config'.

   `RSPEC errors': some series of USR Sportsters and early Couriers
have bugs in the handling of the `AT+FCC' command.  It's meant to
specify the maximum transmission speed, like "14400", but these modems
interpret it as *minimum* speed, so they fail if sending to a machine
that can only do 9600 bps.  If you see RSPEC errors in the sendfax log
(+FHS:24), try the setting `modem-quirks 0x20' in `sendfax.config'.
This will tell `sendfax' not to set the corresponding `AT+FCC'
parameter.

   The USR modems support Caller ID delivery (both the I-Modem series
and the analog ones).  Switch it on with `AT#CID=1' and mgetty should
automatically be able to recognize the incoming caller ID.  If not, show
me a detailed log file...

   Firmware upgrades and documentation are available on `ftp.usr.de' in
the directory `/pub/USRobotics/modem/...'.


File: mgetty.info,  Node: Elink-ISDN,  Next: i4l,  Prev: USR,  Up: Modems

5.1.18 Elink ISDN Terminal Adaptors 293, 310, 393 with X.75 and V.110
---------------------------------------------------------------------

The TA's are connected to national German ISDN (1TR6) or Euro-ISDN. The
host side is a standard serial port with an AT-command set, letting them
look like a conventional modem. Therefore they are often (wrongly)
called 'ISDN modems'.

   It is strongly recommended to feed them with 115k2 bps, else only
V.110 (38k4 bps) is available. Configuration may differ slightly,
depending on which of those Elinks is used, wether it is connected to
Euro-ISDN or 1TR6 and last but not least they are still under
developement, so you're on your own with that.

   ISDN generally supports two nice features: first it is now possible
to check callers number, which may be used to identify callers, second
ist the charge service, where it is possible to request the amount of
charge units for the call. For mgetty the second one is only from minor
interest, but the first one is.  The opposite phone number will be
shown with the command `AT\O'. If a call comes in, `AT\OA' will answer
the call, display caller's id in a 'digit only' (e.g. `04419808550')
form and then print out the `CONNECT'-String.

   To enable mgetty to utilize this, the "get caller ID" sequence must
be set up accordingly and the `CND' feature must be enabled:

   Use `get-cnd-chat "" AT\\O OK' in `mgetty.config', and make sure
that `#define CNDFILE ".../dialin.config"' at the end of `policy.h' is
enabled.

   If you only want to grab the phone number and not check it against
`dialin.config', you can try playing with something like  `answer-chat
"" AT\\OA CONNECT \c \r' in `mgetty.config'.

   Having a glance at the output of `AT I4'-output of the Elink, it
looks as if it is able to support Fax-Service too, but there is no hint
in the manual. So mgetty will likely put itself into data-only mode. (I
got some information from the Elink people that some of the Elinks have
a data/fax analog modem built in, which should work nicely with the fax
part of `mgetty', but I didn't try yet.)

   (Thanks to Ulrich Tieman, lord@olis.north.de, for this section.
Don't ask me, ask him if you use an ELINK)


File: mgetty.info,  Node: i4l,  Next: i4l-capi,  Prev: Elink-ISDN,  Up: Modems

5.1.19 ISDN 4 Linux support
---------------------------

`mgetty' and `sendfax' work with isdn4linux (i4l), but there are a
number if things to point out.

   For data calls via ISDN V.110 or X.75 async modem emulation, you can
put mgetty on a `/dev/ttyI*' device and mgetty will handle so-called
"asynchronous ISDN" connections fine.  To make sure that mgetty will
pick up the phone, set your local ISDN number with `AT&E<number>' from
`init-chat' (otherwise isdn4linux will just ignore incoming calls).

   As far as I can see, i4l will always signal the caller ID for
incoming calls as "CALLER NUMBER: ..." to mgetty.  Mgetty can handle
this just fine.

   If you want to see the destination number for incoming calls, add
`ATS23.2=1' to the `init-chat'.  This will make i4l signal the dialed
MSN number as `CALLED NUMBER: 12345', and mgetty will then pass it on
as $CALLED_ID to fax scripts and so on.  This is implemented since
Linux 2.4.10, or in earlier Versions with Jan Oberlaender's patch
(http://www.stud.uni-karlsruhe.de/~uslk/i4l-callednumber.tar.gz).
(*NOTE*: This doesn't seem to work for at least Linux 2.4.20 as shipped
by RedHat 8.0 - anyone with some details??!)

   Alternatively, you can set `ATS23.0=1'. This will make i4l signal
the dialed MSN number as `RING/12345'.  This was problematic in the
past, as lots of other modems have a similar format to report the
Caller ID (like `RING;4321' in ELSA modems) but recent mgetty versions
handle this properly.  With this, you can run a single mgetty instance
for all your telephone numbers: just set `AT&L*' in your init string -
this tells isnd4linux that *all* incoming calls are to be signalled to
mgetty, not only specific MSN.

   For the full list of available AT commands, consult the i4l docs
(for example in `/usr/src/linux/Documentation/isdn/README'.

   For ISDN PPP calls with synchronous PPP (which is the "normal" way
to do PPP over ISDN), you do *not* need `mgetty'.  PPPoISDN calls are
handled by `ipppd', which is part of isdn4linux.  Mgetty can only
handle PPP-over-X.75 or PPP-over-V110, which is something that is only
used for WAP connections or with old terminal adaptors.

   Fax support with isdn4linux is a tricky issue.  For most ISDN cards,
this will *NOT WORK*.  It only works for cards that have a fax chip (or
separate CPU) on board, and can be accessed with the fax class 2/2.0
command set.  It will work fine with the Diehl Server BRI ISDN card
(active), and that's the only card I know that will work as of June
2001.  Accessing ISDN fax via CAPI is NOT supported (see below).

   There's a small catch: modem autodetection will make mgetty think
that your ttyI device doesn't support fax (because most cards can't do
it).  So you need to set `modem-type cls' in `mgetty.config' and/or
`sendfax.config' to force class 2 mode.  Class 2.0 mode is not
supported.

   Voice support with `vgetty' should work (use your ttyI device as an
answering machine, etc.).  I have not tried it yet - talk to the mgetty
or i4l mailing lists if it doesn't work.


File: mgetty.info,  Node: i4l-capi,  Next: Class 1,  Prev: i4l,  Up: Modems

5.1.20 ISDN 4 Linux with CAPI
-----------------------------

Some of the ISDN card manufacturers have pushed to adapt the windows
Common ISDN API (CAPI) to Linux.  This in itself is not bad, but it has
a nasty side effect: less energy is invested to provide a useful Fax
Class 2 support for the active ISDN cards that can do fax.  Some cards
don't have Fax Class 2 at all, and for some cards the Class 2 support
is quite broken.

   So you might end up with a nice fax-capable card and no ttyI / Fax
Class 2 support for it...

   `mgetty+sendfax' will, as of 1.1.31, *NOT* work with a CAPI
interface.

   One of the problems with CAPI is that it is the wrong sort of
abstraction for the purpose of sending a fax.  The call setup part
(dialing up) needs far too much attention for ISDN protocol details, and
the actual fax transmission part is far too automated - the CAPI doesn't
provide proper feedback about what's going on in the fax layer, like
"the client requested a retransmission of page 2, and the connection
was lost in the middle of page 4" - all you get is "success/failure"
and the number of pages transmitted (including retransmissions - which
makes this figure less than useful).

   If you need to use fax with CAPI, take a look at the "capifax"
software available on `ftp://ftp.isdn4linux.de/pub/capi4linux' (not
written by me, but it works).  The stuff works with a CAPI-specific
file format called "SFF".

   Conversion to SFF can be done with recent ghostscripts (cfax driver),
and conversion from SFF to G3 can be done with the `sff2g3' program
which comes with mgetty.  (I needed something like this for a customer
project, and the existing SFF-to-something converters were all much to
heavyweight - requiring tons of additional libraries, C++ converters,
and whatnot.  My sff2g3 is 330 lines of code, needs no external
libraries and only an ANSI C compiler.  Beat that :-) ).

   Chances are good that I will eventually hack `capifax' into something
that's call-compatible to `mgetty' (for fax reception) and `sendfax'
(for fax sending).  But this depends somewhat on customer demand, read:
paid-for time.


File: mgetty.info,  Node: Class 1,  Prev: i4l-capi,  Up: Modems

5.1.21 Class 1 Faxmodems
------------------------

These do not work. They are not going to be supported (class 1 faxing is
a mess, and the timing is extremely critical--nearly impossible in a
unix environment--read the comments to the FlexFax/Hylafax package for
details).

   Update: some very preliminary support is in the code now.  It's known
to be incomplete in a large number of places.  If you feel adventurous,
compile mgetty with `-DCLASS1', and try it - but I will NOT give
beginner-level support here.  If it doesn't work, send the log file of
a problematic call, unmodified and complete, at debug level 6.


File: mgetty.info,  Node: Systems,  Next: General,  Prev: Modems,  Up: Problems

5.2 Operating Systems
=====================

This section describes problems that have occured while porting the
package to various operating systems.

* Menu:

* OS-Generic::      Problems and mistakes common to all operating systems
* SCO-322::         SCO Unix 3.2.2 (ODT 1.0 / 1.1)
* SCO-324::         SCO Unix 3.2v4 (ODT 2.0 / 3.0)
* Linux::           Linux
* ISC::             ISC
* SVR4::            SVR4 Unix
* SVR42::           SVR4.2 Unix - Onsite, UnixWare, ...
* BSD::             BSD-like flavours of Unix
* AIX::             IBM's AIX Operating System
* SunOS::           SunOS 4.1.1 and up
* Solaris2::        SunSoft Solaris 2.3 and up
* 3b1::             AT&T 3b1
* HP-UX::           The HP-UX operating system
* NEXTSTEP::        The NEXTSTEP operating system
* Darwin::          Apple's MacOS X / Darwin operating system

   If your system is not in the list, that doesn't mean it won't work.
It just means that I didn't get a report (or a port) for that system
yet.

   mgetty+sendfax should work on most unixoid operating systems, as
long as they provide `SysV termio' or `POSIX termios' call for tty
management. `BSD sgtty' support isn't finished yet.

   For best results, your system should have `select(S)' or `poll(S)',
but if both functions are not available or don't work on ttys
(`poll(S)' is known to do this on SVR3.1 and earlier), you can use a
kludge, `-DUSE_READ'.

   Besides that, you'll need some fiddling with the header files to get
all defines and prototypes right.

   Further, you'll have to check `tio.c', function
`tio_set_flow_control()', whether the way hardware flow control is
activated works on your system. Most likely, it won't -- that's one of
the major portability problems. If you change something and get it to
work, please send me patches. (You're welcome to do so anyway).


File: mgetty.info,  Node: OS-Generic,  Next: SCO-322,  Prev: Systems,  Up: Systems

5.2.1 Generic problems and common mistakes
------------------------------------------

There are a few things that can go wrong on all supported operating
systems. This section is meant to give a few hints how to find them.

   * `mgetty' is correctly set up in `/etc/inittab', but `ps' doesn't
     list `mgetty' anyway.

     This is usually caused by not notifying the `init' of your changes
     to `/etc/inittab' (or `/etc/ttytab' on BSD). You have to signal
     `init' with a HUP signal (`kill -1 1') that it should re-read this
     file.

   * `mgetty' is setup correctly, runs a while, then stops being listed
     by `ps', and `init' complains something like `respawning to fast,
     disabling ...'.

     This means, there is an error in the mgetty set up. If the `mgetty'
     process quits too fast (because of an error), and too often in a
     row, `init' will assume that something is going crazy, and disable
     the process. You can re-enable it with `kill -1 1', but you should
     check the mgetty log file (!!!!!) before, to find out *why* it
     failed in the first place


File: mgetty.info,  Node: SCO-322,  Next: SCO-324,  Prev: OS-Generic,  Up: Systems

5.2.2 SCO Unix 3.2.2 (ODT 1.0 / 1.1)
------------------------------------

No major twiddling needs to be done. If your `select()' refuses to
sleep less than one second, use poll(S) instead (set `-DUSE_POLL' in
the CFLAGS section of `Makefile').

   Use the modem-control devices for mgetty and dial-outs (e.g.
`/dev/tty2A'), or (far better), use FAS with minor number of 80+port,
using full RTS + CTS handshake, and non-blocking opens (`/dev/ttyF01')
- the original SCO serial driver is slow, unreliable and doesn't do
proper hardware flow control. *Note SCO-324::.

   Ignore all the warnings about "passing arg 2 of signal from
incompatible pointer type". They are caused because the SCO 3.2.2
development system header files are somewhat unusual.

   If it doesn't work, or some weird things happen on login (e.g.,
zmodem downloads do not work), try compiling with -DSYSV_TERMIO. I had
some problems with Posix termios on SCO ODT 1.0.


File: mgetty.info,  Node: SCO-324,  Next: Linux,  Prev: SCO-322,  Up: Systems

5.2.3 SCO Unix 3.2.4 (ODT 2.0 and ODT 3.0)
------------------------------------------

I'm using mgetty on SCO 3.2v4(.2) (in fact, developing it there), so be
assured: it works.

   I consider the way that hardware flow control is handled on SCO to be
broken, so I _strongly_ recommend using the `FAS' serial driver
(version 2.11 or higher, earlier versions may crash the system), to be
found on your nearest comp.sources.unix archive. With `fas', use the
devices with a minor number of `80+port number' for best results. Make
sure that your modem enables the `DSR' line, because otherwise, `FAS'
won't do hardware handshake.

   If you don't use `fas', I've been told that you have to use the
`modem control' lines, that is, the "uppercase" lines, e.g.
`/dev/tty1A', because SCO's serial driver won't do any hardware flow
control at all on the "lowercase" lines. Be warned, the driver will also
disable hardware flow control if you use Xon/Xoff flow control (no way
to use both). Since I do not have a SCO system without `fas', I'd like
to hear very much about results on one.

   Also, you've to define `LOCKS_LOWERCASE', since that's the convention
on SCO Unix and most other programs expect it.

   If mgetty works only partially, but hangs the moment `/etc/issue' is
printed, before the `system!login:' prompt is output, you may have to
change the following line of `mgetty.c' (around line 780):

             /* honor carrier now: terminate if modem hangs up prematurely
              */
             tio_carrier( &tio, TRUE );

   to:

             tio_carrier( &tio, FALSE );

   But before you do this, make sure that your modem enables the CD line
while a carrier is present (Hayes modems: `AT&C1') and also enables the
DSR line (otherwise the port will block once `CLOCAL' is removed).

   This could have been a problem specific to Uwe's dumb AST-compatible
fourport card, but I do not think so.

   Compilation issues:

   Ignore warnings about `struct utimbuf' and `struct timeb', they are
caused by improper include files. On SCO 3.2v4.2, ignore the warnings
about the getopt() prototype, or change prototype or include files.

   Installation:

   SCO provides two utilities to manipulate `/etc/inittab', `enable'
and `disable'. Those tools work only if you have specified a gettydefs
tag on the `mgetty' command line, otherwise they will complain about
"not a valid tty". So, either append the gettydefs tag (`mgetty' will
ignore it if not compiled with `USE_GETTYDEFS') or change
`/etc/inittab' manually.


File: mgetty.info,  Node: Linux,  Next: ISC,  Prev: SCO-324,  Up: Systems

5.2.4 Linux
-----------

In current stable kernels (i.e. the latest 2.0.xx release or even one
of the 1.2.xx series) and current shared libraries (libc version 5.x)
there should be no bug to interfere with this software.

   If you have a really old Linux system, notice that Linux kernel
versions prior to 0.99pl15 have a bug in the serial handshake code,
that is, if the `CRTSCTS' flag is set, software flow control (XON/XOFF)
won't work. The alarm() call is broken in 4.1 and 4.4.2 libraries,
which sometimes results in aborting the fax receiving.

   On very recent systems using the GNU Libc, you *must* use mgetty
1.1.10 or higher, as the timeout handling on all previous versions
doesn't work under glibc.  Unfortunately, this means that the version
of mgetty shipped with RedHat 5.0 (1.1.9) won't work. Upgrade!

   Hardware handshake (RTS+CTS) on Linux works flawlessly (but only if
mgetty is compiled with POSIX_TERMIOS, but that is default on Linux
anyway). Nevertheless, the `scrts.c' program in `contrib/' is still
provided, it has some other uses, too.

   Linux has no poll(S), so, don't #define `USE_POLL', and the default,
`USE_SELECT', will be used.

   *Important note:* Use the `/dev/ttyS*' devices for getty and for
dial-out (that is, for kermit, uucico, cu, seyon, ...) - *never* use
`/dev/cua*'. Dialing out on `/dev/cua*' will result in the error
message "device busy". (There are reasons why `mgetty' cannot use the
"`ttyS*' vs. `cua*' kernel locking mechanism", see below). If *all*
programs agree on using `/dev/cua*' only, it will work, too - but they
have to agree on one variant.

   For some background about `ttyS' vs. `cua', you might want to read a
mail from the author of the Linux serial drivers, Ted Ts'o, posted to
the Linux-PPP mailing list. I have included it in `doc/ttyS-cua.txt'.

   Some guys seemingly can't resist posting misinformation to the net
all the time, don't believe 'em. The `/dev/cua*' devices are *not*
different from the `/dev/ttyS*' devices concerning data flow or modem
control lines. The only difference is how the device reacts if you do an
`open()': Opening `/dev/ttyS*' normally blocks until the "carrier
detect" line goes active (unless `open()' is called with the `O_NDELAY'
flag; `mgetty' and all dial-out programs do that), and opening
`/dev/cua*' will return an error message (`errno=EBUSY') if another
process has the device already open, thus _preventing dial-out on
`/dev/cua*'_ if `mgetty' is active on `/dev/ttyS*'.

   We use `/dev/ttyS*' all the time for dial-in _and_ for dial-out, and
believe me, it works, and it's the _only_ combination that will work
properly. The kernel locking mechanism only works if you use modem
auto-answer (the getty process sleeps until the modem gets a carrier),
and mgetty uses manual answer (it waits for the RING message from the
modem), which will save your callers a lot of grief because their calls
will only be answered if your computer is ready to receive a call. Part
of the motivation for writing mgetty was being tired of losing lots of
money for useless calls to a hung machine.

   I'd recommend against using `/dev/modem' as a link to the real
device, but if you do that, make it a *hard link* to the appropriate
`/dev/ttyS*'. A soft link will cause problems with the device ownership
because of a peculiarity in the linux `chown()' implementation (that I
refuse to work around).

   If you get into trouble with write permissions on ttySx, you may add
a new group `dialout' to `/etc/group', then `chown .dialout /dev/ttySx'
your device, and add your users to the dialout group. Don't forget to
add the system user `uucp' to that group (UUCP needs to have modem
access), and make sure, `port-group' in mgetty's configuration file is
set up correctly.  The concept of such a dialout group is already used
in most Linux distributions today.

   There are various different `init' and `last' programs out there,
some work with mgetty, some don't. If you get some strange output from
`who' or `last' and are using a different `init' program than the `sysv
init', try to define `-DNO_SYSVINIT'. That should help.

   I've been told that it's necessary to do that if you use the
`simple-init'.

   Anyway, I can only *strongly* recommend to switch over to `SysVinit'
if you use `simple init', since the latter seems to be severely broken
regarding utmp and controlling tty handling.

   If you have problems because of an uninitialized `TERM' environment
variable (which really isn't getty's job, but `getty_ps' insists on
doing it, and people rely on it), use the `term ...' config file option
to set it according to your needs.

   If you're experiencing problems with hanging `/bin/login' processes,
*Note login-hang::.

   Recently, I have received a number of bug reports concerning
operation in systems using one or more *Cyclades serial boards*.  There
is some incompatibility between the standard Cyclades driver and the
GNU CC 2.7.2, which can result in system lockups.  Upgrade to the very
latest Linux driver, which can be found on ftp.cyclades.com.  I have
received reports that the driver version 2.1 works fine (85 modems on
one system, connected to 3 Cyclom Ye boards!).


File: mgetty.info,  Node: ISC,  Next: SVR4,  Prev: Linux,  Up: Systems

5.2.5 ISC
---------

The ISC port has been done by Russell Brown, russell@lutton.lls.com.
Thanks!

   First of all, define `-DISC' in the Makefile. This will take care of
some minor problems. Then, link with `-linet -lpt'.

   If you have a ISC Unix 4.0, you may have to define `-D_POSIX_SOURCE'
to get around some include file problems and link `-lcposix'.

   If you have problems with the AWK programs in the `fax/' shell
scripts, try defining `AWK=nawk' in the `Makefile'. That should take
care of those problems.

   Again, for best results I recommend using the FAS serial driver, and
using a port with a minor number of 80+portno (ttyF01 etc.)

   If you use a Digiboard smart serial cart (e.g. the digiboard pc/8e),
use the `/dev/ttyi*' devices instead of `/dev/cui*', becaus only the
former ones honour carrier drops (If you use `cui*', your processes
won't die if the modem unexpectedly hangs up)


File: mgetty.info,  Node: SVR4,  Next: SVR42,  Prev: ISC,  Up: Systems

5.2.6 SVR4 Unix
---------------

mgetty has been ported to SVR4 now (many thanks to Bodo Bauer,
<bodo@hal.nbg.sub.org>, Martin Husemann, <martin@bi-link.owl.de> and
Marc Boucher <marc@cam.org>).

   As far as I know, it's sufficient to add `-DSVR4' to the CFLAGS in
Makefile. If you have any problems or suggestions, please report them
also to the people above, since I do not have a SVR4-System to run
tests on.

   If you use the `SAS' serial driver (streams-version of `FAS') and
want to force `sas' to use hardware-handshake all the time, use a
device with a minor device number of `80+port number' (see the `sas'
manual for explantations). If you use a port with a minor device number
of `7*16+i', `mgetty' is able to switch hardware handshake on and off
according to the flags set in policy.h, using `sys/termiox.h'. (Well,
it works - but apparently fax reception doesn't work with this minor
device number. Symptom: only one byte is received during fax reception
(0x00). Anybody any clue?).

   If you use `FAS', use the devices with a minor device number of
`80+port number' (as usual).


File: mgetty.info,  Node: SVR42,  Next: BSD,  Prev: SVR4,  Up: Systems

5.2.7 SVR4.2 - Onsite Unix, UnixWare, ...
-----------------------------------------

Basically, SVR4.2 is quite similar to SVR4, but you have to watch out
for some details (defining `-DSVR42' in the Makefile will do it for
you).

   Most important, the _termiox_ interface via the `TCGETX' / `TCSETX'
`ioctl()'s does not seem to work any longer - the calls return an
error, and the port behaves strangely. If you're experiencing this,
please try commenting out the corresponding code in `tio.c', funtion
`tio_set_flow_control()' and mail me whether that make it work.

   Further, ussing `USE_POLL' or `USE_READ', won't work. The default of
`USE_SELECT' is OK.

   To enable hardware handshake, use the tty device with the trailing
"h", e.g.  `tty01h'. On the other one (`tty01'), the driver won't do
H/W handshake.

   Depending on the configuration, parallel dial-out with Taylor-UUCP
may fail (uucico complaining that it cannot set `CLOCAL'), in that
case, you've to recompile Taylor with different settings for the
`termio' selection (POSIX vs. SYSV).

   Many thanks to Joerg Weber (joerg@interface-business.de) for finding
all those problems.

   Ed Hall (edhall@rand.org) found another major glitch on UnixWare
4.2: if you run `sendfax' without setting `ignore-carrier true' in
`sendfax.config', and `sendfax' switches off carrier detection at the
end of the very last page, the kernel code messes up something and
bytes get lost. The modem then returns funny error codes, like, for
example,
     Transmission error: +FHNG:44 (Unrecognized Transparent data command)
   If you're experiencing this, just set `ignore-carrier true' and
everything should work just fine (please tell me in any case whether it
was necessary, because if it happens for other people as well, I'll
make this permanent on SVR42).

   *Note Solaris2::.


File: mgetty.info,  Node: BSD,  Next: AIX,  Prev: SVR42,  Up: Systems

5.2.8 BSD-like flavours of Unix
-------------------------------

A port to 386BSD, NetBSD, FreeBSD has been done by Martin Husemann,
martin@bi-link.owl.de, and Gunther Shadow,
gusw@fub46.zedat.fu-berlin.de.

   I think it works quite well, except that the `VTIME' mechanism to
timeout `read()' calls doesn't work in older *BSD versions. If `mgetty'
hangs, with the last line in the log file being something like "waiting
for line to clear", upgrade your kernel, or, if you can't do that,
compile `mgetty' with `-DBROKEN_VTIME' (in that case, select() will be
used).

   For older versions of BSD Unix that do not have `termios.h', you'll
have to complete the unfinished support for `sgtty.h' in `tio.c' and
`tio.h'.

   Generally, BSD Unices do not have a `/etc/inittab' as system V has.
Instead, they have `/etc/ttys' (or sometimes `/etc/ttytab' on really
old BSD systems). Thus, you have to enter a line like
     cua0    "/usr/local/sbin/mgetty -x 3 cua0"       vt100
   or
     cua00	"/usr/local/sbin/mgetty -x 3"    vt100 on insecure
   there. See the corresponding manpage for an exect description of the
files format on your system. Don't forget to remove (or comment out) the
original getty on the corresponding `/dev/tty*' line.


File: mgetty.info,  Node: AIX,  Next: SunOS,  Prev: BSD,  Up: Systems

5.2.9 IBM's AIX Operating System
--------------------------------

Chris Lewis, Harald Milz and Michael Staats have done excellent work on
porting `mgetty' to AIX.   Since then, I have taken over and actively
use mgetty+sendfax on AIX for customer systems, and everything is very
well tested now.

   On AIX, many people do not want to manipulate `/etc/inittab'
directly, instead,  use some system administration tools (like 'smit').
To ease `mgetty' installation on AIX, Michael Staats has provided a
small shell script, `inittab.aix', that will help you setup your
`inittab' after you've run `make install'. Just call it with the name
of the tty you're modem is connected to, e.g.

   `./inittab.aix tty0'.

   I have received a couple of problem reports on AIX 4.1 where
"suddenly" the modem line stopped working and all mgetty reported were
error messages. If that happens to you, set `toggle-dtr no' in
`mgetty.config'. AIX 4.1 doesn't seem to like programs that fiddle with
the modem control lines.

   Christoph Brinck (cb@medat.de) has also reported that it's necessary
to enable the "dtropen line discipline" for the serial line you're
using (whatever that may mean). This is done with the command:

     chdev -l 'tty1' -a flow_disp='rts'
     chdev -l 'tty1' -a open_disp='dtropen'

   or via the `chgtty' part of `SMIT' (but I think that's the default
setting for new ttys anyway).

   Hardware and Software flow control work fine on AIX 3.x and AIX 4.x
now.


File: mgetty.info,  Node: SunOS,  Next: Solaris2,  Prev: AIX,  Up: Systems

5.2.10 SunOS 4.1.1 and up
-------------------------

mgetty has been ported to SunOS, and seems to work quite well.  If you
use SunOS, please send me a brief report about your results.

   Thanks to Earl Hartwig, earl@fozzi.ocunix.on.ca, for the initial
port.

   For compilation, please define `-Dsunos4'.

   In `policy.h', you've to adapt the location of the LOCK files.

   In the Makefile, set `ECHO='...'' to `/usr/5bin/echo', because the
standard one doesn't support escape codes like `\n' or `\c'.
Alternatively, if you don't have the System5 options installed, use
`mg.echo'.

   If a fax reception hangs shortly after the `+FCON' is seen, please
try setting `FAXREC_FLOW' to Xon/Xoff (`FLOW_SOFT'). Hardware handshake
has problems on SunOS versions without the "Jumbo TTY" patch.

   If fax sending hangs mysteriously between the first and the second
page, you're likely to have a modem that drops DCD during pages. As
SunOS' serial drivers are dumb, reception of data will fail if DCD is
low and handshake is set to RTS/CTS. So, set `ignore-carrier yes' in
`sendfax.config' *and* `#define FAXSEND_FLOW FLOW_SOFT' in `policy.h'
and fax sending should work.

   Please use the "outgoing" devices (`/dev/cua*') for mgetty and
dial-outs, using the "incoming" devices (`/dev/tty*') will make dialout
impossible. Further, carrier detect (DCD) is only honoured on the
`cua*' lines.

   It is *very* strongly recommended that you install the "jumbo tty
patch" (patch number 100513-05 for 4.1.2 or .3, patch number 101621-01
for 4.1.3_u1 and up) because it will fix a lot misbehaviour of the
serial line drivers.

   Please read also the generic BSD section.


File: mgetty.info,  Node: Solaris2,  Next: 3b1,  Prev: SunOS,  Up: Systems

5.2.11 Solaris 2.3 and up
-------------------------

mgetty runs successfully and without trouble under Solaris 2.3, 2.4 and
2.5.1 (later versions should also work, but I didn't get any report so
far).  For compilation use `-Dsolaris2'. With Solaris 2.3 it's
recommended to use GNU gcc, but with Solaris 2.4 it compiles fine with
the SPARCompiler C 3.0.1.  Define `CC=cc'.

   In `policy.h' you have to define `term/a' or `term/b' as
`FAX_MODEM_TTYS'. Don't use the outgoing devices `/dev/cua/*'!!

   As `DEVICE_GROUP' you should configure `uucp'.  If you want allow to
normal users to dial out, add all users allowed to do that, to the group
`uucp'. Then it's important to change the permissions of
`/var/spool/locks' from the default permissions `drwxr-xr-x' to
`drwxrwsr-x'. Make sure that it's owned by `uucp.uucp'.  Otherwise no
one wanting to dial out is able to create a lock file.  The `FILE_MODE'
in `policy.h' must be `0660' as well.

   If you don't want allow anyone to dial out you should set `FILE_MODE'
to `0640' or `0600'.

   For the "notify mail" message to look best, define `MAILER' in
`policy.h' to /USR/LIB/SENDMAIL and define `NEED_MAIL_HEADERS'. So a
proper subject header is created.  Nevertheless, `/usr/bin/mailx'
works, as it is the default for SVR4.

   If everything compiled well and you did `make install', you have to
add an entry to `/etc/inittab' like the following:

     ya:234:respawn:/usr/local/sbin/mgetty -s 38400 -x 3 term/a

   _Don't use the Solaris `admintool' to create any port monitoring
entries in `/etc/saf/_sactab' and `/etc/saf/zsmon/_pmtab'._

   Many thanks to Stefan Muehlenweg (muehlenw@samhh.hanse.DE) for this
section.

   Solaris (as all Sun operating systems) seems to be somewhat weird
concerning its handling of the RTS line.  I have received two reports
that 'sometimes' a modem hangs during initialization, and won't talk to
mgetty anymore.  In these cases, the problem went away when the modem
(an USR Sportster) was set to `AT&R1', which means 'ignore RTS line'.
Thanks to Valerio Di Giampietro for detailing this.


File: mgetty.info,  Node: 3b1,  Next: HP-UX,  Prev: Solaris2,  Up: Systems

5.2.12 AT&T 3b1
---------------

Glenn Thobe and Chris Lewis have ported mgetty+sendfax to AT&T's 3B1
machines, it should compile without changes to the source (but define
-D_3B1_ in the Makefile).

   These ports are to two different environments:

   Glenn's port was with GCC (ANSI C) and an add-on select() library
routines.  Chris's port was with stock 3b1 C, without select().  Both
seem reliable.

   Some further hints concerning a select() library and the pbmplus
tools can be found in the file `contrib/3b1' which are the notes from
Glenn's port.

   Chris's port relies simply on the suggested definitions (especially
`-DUSE_READ') in the Makefile.  Chris suggests that you use select() if
you already have it for some other reason, but that it seems to work
just fine without it.

   Right now, I think mgetty won't compile with the standard C compiler
(it will with gcc), because the stuff I do in the `conf_*.c' source
files is a little bit too hard for it. I'll work on it.


File: mgetty.info,  Node: HP-UX,  Next: NEXTSTEP,  Prev: 3b1,  Up: Systems

5.2.13 The HP-UX operating system
---------------------------------

`mgetty' runs on HP-UX, but that's very much all I can say about it (I
don't know anything about HPs, except that they are somewhat strange).

   Currently, documentation for HP-UX is a bit lacking - if you know
something about `mgetty' on HP-UX, please contribute.


File: mgetty.info,  Node: NEXTSTEP,  Next: Darwin,  Prev: HP-UX,  Up: Systems

5.2.14 The NEXTSTEP operating system
------------------------------------

NEXTSTEP is lacking quite a few commands used by mgetty and its tools:
Luckily, they are available from the GNU project (please mail me if I
forgot any), e.g. gawk, cut (from textutils), id and logname (from
sh-utils). All of them can be compiled for NEXTSTEP without problems,
and it's certainly a good idea to install them anyway. ghostscript
needs some fiddling for NEXTSTEP, but it's available precompiled on the
arcives as GSPrintFilter.  If you don't intend to use faxspool and
friends, you may succeed without installing the forementioned utilities.

   Having said this, there are two different ways to compile `mgetty'
for NEXTSTEP, each with their pros and contras:

   * With termios interface: To use `mgetty''s termios interface (the
     default), you have to link against NEXTSTEP's buggy POSIX library.

     In the Makefile, add "-posix -DBSD" to CFLAGS and LDFLAGS.

     Drawbacks: The log file will be corrupted due to an append bug in
     libposix.

     Use this only if you want to try vgetty. In all other cases it's
     probably better to choose the second variant:

   * With sgtty interface: Ben Stuyts `benst@stuyts.nl' has done an
     effort to make a `mgetty' port using the BSD sgtty style interface
     to the serial ports. This port doesn't need the POSIX library.

     In the Makefile, add "-DNEXTSGTTY -DBSD".

     This port has been tested with m68k and i386 machines.

     For i386 machines, you may want to use the /bin/login replacement
     `modem-login' in `mgetty''s contrib directory. NEXTSTEP's login
     has problems with 8-bit logins. I've got one report from Ben
     Stuyts, though, that `modem-login' does fix problems on "Black
     NeXT"s as well. Just try it.

     Drawback: You can't compile vgetty with sgtty support yet! If you
     want to use vgetty with NEXTSTEP, you'll have to stick with the
     termios port. There are problems with the LNOHANG bit not being
     acknowledged correctly, therefore hanging the modem when the
     caller hangs up.

   For i386 machines, it's wise to use the /dev/cudfX (hardware flow
control,...) devices. I'm using them with NeXT's most recent serial port
driver, Mark Salyzyn's Mux driver also supports them.

   For m68k machines, you have to stick with /dev/cufa.

   This are the settings I use in the Makefile:

     CC=cc
     CFLAGS=-DNEXTSGTTY -DBSD -O2  (-posix -DBSD for termios port)
     INSTALL=install -c -o root -g wheel
     spool=/usr/spool
     SBINDIR=$(prefix)/etc
     ECHO="mg.echo"
     INSTALL_MECHO=mg.echo
     AWK=gawk

   Furthermore, you should define binary lock files, in policy.h:

     #define LOCKS_BINARY 1

   Finally, when using NEXTSTEP's cc, you need to run "make noident" in
the first place to remove the #ident directives from the source files.

   If you have questions, comments or suggestions regarding `mgetty'
with NEXTSTEP, feel free to contact Gregor Hoffleit
`flight@mathi.uni-heidelberg.de' or Ben Stuyts `benst@stuyts.nl'.

   * Coming real soon now:

     How to use `mgetty' to send faxes via the NEXTSTEP fax panel

     (using Kevin Peckover's ps2g3 package, available as
     `ftp://peanuts.leo.org/pub/next/Tools/postscript/ps2g3.s.tar.gz').

   * Coming soon:

     How to patch and use `mgetty' to spool received faxes in the
     NEXTSTEP fax system.


File: mgetty.info,  Node: Darwin,  Prev: NEXTSTEP,  Up: Systems

   If I understand this correctly, "Darwin" is the underlying operating
system that Apple MacOS X is based upon.

   Edwin C Wirth <ecwirth@mac.com> gave me an account to his "Darwin
Kernel Version 5.1" machine (running MacOS 10.1.1 on top of it) so I
could port `mgetty+sendfax' to that OS.  Thanks to that, Darwin is
supported from 1.1.28 on.

   Compilation is pretty straightforward: use the default CFLAGS and
LIBS settings in the Makefile, set `CC=cc', and then run `make'.  It
will spit out a ton of warnings about `undefined or invalid #
directive' - but those are harmless, it's just cpp not understanding
`#ident'.

   At run time, as far as I could see, the internal Mac modem is
available on `/dev/tty.modem'.  The macintosh I had for testing also
had "KeyUSA" USB-to-Serial ports that appeared as
`/dev/tty.KeyUSA28X913.1' and `.2' - so other serial ports should also
appear as `/dev/tty.*' devices.  Note: there seem to be "cu" devices as
well (`/dev/cu.modem'), as in older Linux variants.  I did only try
sending faxes via `tty.modem' yet, but to resolve locking issues, it
might be neccesary to use `cu.*' devices.  To be continued...

   Mgetty should be run from `/etc/ttys' as in other BSDs, see `man
ttys' (there is no `/etc/inittab').

   Open issues:
   * is it better to use `/dev/cu.*' or `/dev/tty.*'?

   * how is tty locking done?  Couldn't find UUCP lock files

   * any tricky things about logging in remotely?  utmp/wtmp?

   * where should the log files go to?  /var/log doesn't seem to exist.


File: mgetty.info,  Node: General,  Next: logfiles,  Prev: Systems,  Up: Problems

5.3 General problems
====================

* Menu:

* pbmtog3::         pbmtog3
* Locks::           Lock files
* login-hang::
* ecu::             ecu (extended cu) 3.20 collides with mgetty


File: mgetty.info,  Node: pbmtog3,  Next: Locks,  Prev: General,  Up: General

5.3.1 pbmtog3
-------------

The `pbmtog3' program from the `pbmplus' distribution produces G3 data
that does not adhere to the T.4 standard. The initial EOL code is
missing, and the lines are not always 1728 pixels wide.  So, some fax
machines won't accept the output at all (not printing even one line),
and others will complain.

   A fix for this problem is available: I have included a patch for
pbmtog3, called `patches/pbmtog3.p1', that will fix the problems. (Oh,
by the way, if you try to send a fax generated with an unpatched
pbmtog3, sendfax will complain that it doesn't like the file ... I've
added a small sanity check to spare me the time browsing through the
logfiles guessing _why_ sendfax failed (won't work if the file has been
processed by `g3cat', though!)). If you use the `pbm2g3' program that is
shipped with `mgetty', there is *no need to patch anything*.

   Basically, there is no need at all to use `pbmplus'' `pbmtog3'
program any more, since `mgetty' includes an own copy. I just wanted to
warn you.

   Anyway, my program is lots faster ....


File: mgetty.info,  Node: Locks,  Next: login-hang,  Prev: pbmtog3,  Up: General

5.3.2 Lock files
----------------

Kermit et.al. cannot dial out while mgetty is running (modem responses
are eaten by mgetty)--what's wrong?

   Most propably, you have not configured the `LOCK' and `LOCKS_BINARY'
defines in `policy.h' properly. Make sure that the lockfiles kermit (or
cu, pcomm, seyon,...) expect are in the path specified in `LOCK' and
set `LOCKS_BINARY' to 1 if they do not write the PID of the locking
process in ascii (10 bytes) to the lock file but as a 4-byte integer
instead. Mgetty and Sendfax will understand both types of lock files,
but if `LOCKS_BINARY' is not set properly, other programs may not
understand the lock file.

   Also, make sure that both processes use the same name for the device.
(i.e., mgetty locking `/dev/ttyS0' and kermit locking `/dev/modem' will
definitely fail.)


File: mgetty.info,  Node: login-hang,  Next: ecu,  Prev: Locks,  Up: General

5.3.3 mgetty works, /bin/login hangs
------------------------------------

A problem seen fairly often on directly connected serial lines (`mgetty
-r'), and seldomly on modem lines, is that `mgetty' works flawlessly,
but `/bin/login' just hangs instead of prompting for the user password.

   The reason for this is that many `login' programs reopen `/dev/tty'
(the controlling tty of a process) to make sure they have full control
over the password entered by the user (for example, to prevent
snooping). This will block on some systems if the DCD (carrier detect)
line coming from the modem or the other machine is low. Notably those
systems are those that have callin/callout device pairs for one serial
device, e.g.  Linux, SunOS, SCO/FAS, etc.

   The fix is easy: make sure that the DCD line is high.

   If you use a modem, the command to do this is usually `AT&C1' (but
check with your modem manual).

   If you're using a direct null-modem connection to another host, the
recommended solution is to wire DCD on your side to the DTR line on the
other side and vice versa. That way, when the remote machine "hangs up"
(calling program exits and DTR drops), your host will get notified as
well. This is what a properly wired (!) "null-modem cable" does anyway.

   If you don't have free lines in your serial cable (classic three-wire
approach), wire DCD to the DTR line on your own host, and make sure that
mgetty won't toggle DTR upon startup (causing a hangup signal!), e.g. by
setting `toggle-dtr no' in `mgetty.config'.


File: mgetty.info,  Node: ecu,  Prev: login-hang,  Up: General

5.3.4 ECU 3.20 or earlier on SCO collides with mgetty
-----------------------------------------------------

ECU releases 3.20 and earlier had a severe bug in the utmp handling that
prevented dialing out on a port that mgetty uses. It has been fixed in
ECU 3.27. If you run into that problem, please get a newer release.
Alternatively, you can use the patch that Uwe Fuerst provided, it can be
found in `patches/ecu320.p1'.


File: mgetty.info,  Node: logfiles,  Next: ftp,  Prev: General,  Up: Problems

5.4 Sample Log files
====================

Both mgetty and sendfax can provide logfiles that can be very helpful
for debugging and accounting purposes. The amount that is logged is
controlled with the default set in `policy.h' and the command line
argument `-x <level>'. Higher numbers give more details.

   At this place, I want to show you some typical cases, so you can
compare your log files to those given here and check what is different.

   (Note: naturally all the modem initializations, and also some of the
modem responses, vary between modem brands!)

   All the mgetty log files have been done with log level `L_MESG',
that is, `-x 4'. The sendfax log file was done with `L_NOISE', `-x 5'.

* Menu:

* log-mgetty-data::  mgetty log file, incoming data call
* log-mgetty-fax::  mgetty log file, incoming fax call (one page)
* log-mgetty-syslog::  mgetty logging to syslog
* log-sendfax::     sendfax log file, sending one page


File: mgetty.info,  Node: log-mgetty-data,  Next: log-mgetty-fax,  Prev: logfiles,  Up: logfiles

5.4.1 mgetty, incoming data call
--------------------------------

This is a log file of a typical data connection, ZyXEL-to-ZyXEL modems,
connect with 19200 bps on a port speed of 38400, login as "Uartinet",
the login program called is `/usr/lib/uucp/uucico' (controlled by
`LOGIN_CFG_FILE', which directs all login names starting with "U" to
uucico)

     03/03 22:40:15  check for lockfiles
     03/03 22:40:15  locking the line
     03/03 22:40:16  lowering DTR to reset Modem
     03/03 22:40:16  send: \d\d\d+++\d\d\d[0d]\dATQ0V1H0[0d]
     03/03 22:40:20  waiting for ``OK'' ** found **
     03/03 22:40:20  send: ATS0=0Q0&D3&H3&N0&K4[0d]
     03/03 22:40:20  waiting for ``OK'' ** found **
     03/03 22:40:20  send: AT+FCLASS=0[0d]
     03/03 22:40:20  waiting for ``OK'' ** found **
     03/03 22:40:20  send: AT+FAA=1;+FBOR=0;+FCR=1[0d]
     03/03 22:40:20  waiting for ``OK'' ** found **
     03/03 22:40:20  send: AT+FLID="49 89 3243328"[0d]
     03/03 22:40:20  waiting for ``OK'' ** found **
     03/03 22:40:20  send: AT+FDCC=1,5,0,2,0,0,0[0d]
     03/03 22:40:20  waiting for ``OK'' ** found **
     03/03 22:40:20  fax_command: send 'AT+FLPL=1'
     03/03 22:40:20  fax_wait_for(OK)** found **
     03/03 22:40:21  waiting...
     03/03 22:41:28  waiting for ``RING'' ** found **
     03/03 22:41:28  send: ATA[0d]
     03/03 22:41:28  waiting for ``CONNECT'' ** found **
     03/03 22:41:42  send:
     03/03 22:41:42  waiting for ``
     '' ** found **
     03/03 22:41:43 ##### data dev=tty4c, pid=6470, caller=none, conn='38400/ZyX  16800/V42b', name='', cmd='/usr/lib/uucp/uucico', user='Uartinet'


File: mgetty.info,  Node: log-mgetty-fax,  Next: log-mgetty-syslog,  Prev: log-mgetty-data,  Up: logfiles

5.4.2 mgetty, incoming fax call
-------------------------------

This is a log file of a fax call I got today. It was a fax call with
14400 bps (actually, the call came from another faxmodem, but you won't
see that in the log file), using high resolution. One page was
received, the connection time was 33 seconds. No errors occured.

   (All the stuff up to "waiting..." is identical to the example above,
so I don't list it again)

     [...]
     03/03 21:39:32  waiting...
     03/03 21:46:22  waiting for ``RING'' ** found **
     03/03 21:46:22  send: ATA[0d]
     03/03 21:46:22  waiting for ``CONNECT''
     03/03 21:46:32  found action string: ``+FCON''
     03/03 21:46:32  action is A_FAX, start fax receiver...
     03/03 21:46:32  fax_wait_for(OK)
     03/03 21:46:36  fax_id: '+FTSI:+31 20 6147110       '
     03/03 21:46:36  transmission par.: '+FDCS:1,5,0,2,0,0,0,0'** found **
     03/03 21:46:36  fax_command: send 'AT+FDR'
     03/03 21:46:36  fax_wait_for(CONNECT)
     03/03 21:46:37  fax_id: '+FTSI:+31 20 6147110       '
     03/03 21:46:37  transmission par.: '+FDCS:1,5,0,2,0,0,0,0'** found **
     03/03 21:46:38  fax_get_page_data: receiving /usr/spool/fax/incoming/ffd764c9e4d-+31-20-6147110.01...
     03/03 21:46:51  fax_get_page_data: page end, bytes received: 24933
     03/03 21:46:51  fax_wait_for(OK)
     03/03 21:46:51  page status: +FPTS:1** found **
     03/03 21:46:53  fax_wait_for(CONNECT)
     03/03 21:46:55  connection hangup: '+FHNG:000'** found **
     03/03 21:46:56 ##### fax dev=tty4d, pid=4807, caller=none, name='', id='+31 20 6147110       ', +FHNG=000, pages=1, time=00:00:33


File: mgetty.info,  Node: log-mgetty-syslog,  Next: log-sendfax,  Prev: log-mgetty-fax,  Up: logfiles

5.4.3 mgetty, logging into syslog
---------------------------------

If your system has a `syslogd' and the `syslog()' C function, mgetty
can send parts of its log files to the `syslog' (For details, see
comments in `policy.h'). Not all the information from the log file is
logged here (to avoid clobbering the syslog), just errors and so-called
"audit" messages (seen in the log file as lines with "####" at the
beginning). These have a fixed format, and could easily be parsed by a
program. Let me list a few, and then comment them.

     Mar  3 18:36:16 greenie mgetty[673]: failed A_FAIL dev=tty4d, pid=673, caller=none, conn='', name=''
     Mar  3 18:41:56 greenie mgetty[1866]: fax dev=tty4d, pid=1866, caller=none, name='', id='49 89 3243328        ', +FHNG=100, pages=1, time=00:00:29
     Mar  3 21:46:56 greenie mgetty[4807]: fax dev=tty4d, pid=4807, caller=none, name='', id='+31 20 6147110       ', +FHNG=000, pages=1, time=00:00:33
     Mar  3 20:45:59 greenie mgetty[4038]: data dev=tty4d, pid=4038, caller=none, conn='38400/V.32  9600/MNP5', name='', cmd='/bin/login', user='mbox'
     Mar  3 22:41:43 greenie mgetty[6470]: data dev=tty4c, pid=6470, caller=none, conn='38400/ZyX  16800/V42b', name='', cmd='/usr/lib/uucp/uucico', user='Uartinet'

   Those five lines are one failed call, two fax calls, one of them
failed and one successful, and two data calls, one of a human caller,
loggin into the BBS system, and one of a calling uucico.

   It looks very confusing until you understand the system behind it.
The first fields specify date and time, originating host (greenie is my
machine) and program (mgetty). The next field specifies the type of the
connection made: `fax', `data' or `failed' - the latter one usually
means failure to initialize the modem or failure to connect to a
calling modem, resulting in the well-known `NO CARRIER' message...

   The `dev' and `pid' fields specify the line and process ID of the
mgetty process writing that line.

   The `caller' and `name' fields give caller ID information - if none
is available (as it is here in Germany), or if your modem doesn't
handle it, it will list `none' and `''', respectively.

   For fax calls, additional informations given are the remote station
ID (`id='...''), the hangup code (`+FHNG=...', 0 means "ok"), the
number of pages and the connection time.

   For data calls, the string that the modem returned after `CONNECT' is
listed as `conn='...''. The string that was entered at the login prompt
is listed as `user='...'', and the program that is called to do the
login is given as `cmd='...''. Usually this will be `/usr/bin/login'
unless you have some special system setup for fido or uucp callers - as
I have here, as you can see above.


File: mgetty.info,  Node: log-sendfax,  Prev: log-mgetty-syslog,  Up: logfiles

5.4.4 sendfax, sending a single page
------------------------------------

This is a simple one-page fax that I sent some days ago. Just a single
page, f1.g3, to the phone number 2710834. No errors of any kind occured.

     02/18 11:10:05  sending fax to 2710834
     02/18 11:10:06  checking f1.g3
     02/18 11:10:06  makelock(tty4c) called
     02/18 11:10:06  do_makelock: lock='/usr/spool/uucp/LCK..tty4c'
     02/18 11:10:06  lock made
     02/18 11:10:06  fax_open_device succeeded, tty4c -> 4
     02/18 11:10:06  fax_command: send 'AT'
     02/18 11:10:06  fax_wait_for(OK)
     02/18 11:10:06  fax_wait_for: string 'AT'
     02/18 11:10:06  fax_wait_for: string 'OK'** found **
     02/18 11:10:06  fax_command: send 'AT+FCLASS=2'
     02/18 11:10:06  fax_wait_for(OK)
     02/18 11:10:06  fax_wait_for: string 'AT+FCLASS=2'
     02/18 11:10:06  fax_wait_for: string 'OK'** found **
     02/18 11:10:06  fax_command: send 'AT+FLID="49 89 3243328"'
     02/18 11:10:06  fax_wait_for(OK)
     02/18 11:10:06  fax_wait_for: string 'AT+FLID="49 89 3243328"'
     02/18 11:10:06  fax_wait_for: string 'OK'** found **
     02/18 11:10:06  fax_command: send 'ATL7M1'
     02/18 11:10:06  fax_wait_for(OK)
     02/18 11:10:06  fax_wait_for: string 'ATL7M1'
     02/18 11:10:06  fax_wait_for: string 'OK'** found **
     02/18 11:10:06  fax_command: send 'AT+FDCC=1,5,0,2,0,0,0,0'
     02/18 11:10:06  fax_wait_for(OK)
     02/18 11:10:06  fax_wait_for: string 'AT+FDCC=1,5,0,2,0,0,0,0'
     02/18 11:10:06  fax_wait_for: string 'OK'** found **
     02/18 11:10:06  fax_command: send 'AT+FBOR=0'
     02/18 11:10:06  fax_wait_for(OK)
     02/18 11:10:06  fax_wait_for: string 'AT+FBOR=0'
     02/18 11:10:06  fax_wait_for: string 'OK'** found **
     02/18 11:10:06  fax_command: send 'AT&H3D2710834'
     02/18 11:10:06  fax_wait_for(OK)
     02/18 11:10:07  fax_wait_for: string 'AT&H3D2710834'
     02/18 11:10:39  fax_wait_for: string '+FCON'
     02/18 11:10:39  fax_wait_for: string '+FNSF:00 00 00 00 '
     02/18 11:10:39  fax_wait_for: string '+FCSI:       49 89 2710834 '
     02/18 11:10:39  fax_id: '+FCSI:       49 89 2710834 '
     02/18 11:10:39  fax_wait_for: string '+FDIS:1,3,0,2,0,0,0,4'
     02/18 11:10:39  fax_wait_for: string 'OK'** found **
     02/18 11:10:39  fax_send_page("f1.g3") started...
     02/18 11:10:39  fax_command: send 'AT+FDT'
     02/18 11:10:39  fax_wait_for(CONNECT)
     02/18 11:10:39  fax_wait_for: string 'AT+FDT'
     02/18 11:10:45  fax_wait_for: string '+FDCS:1,3,0,2,0,0,0,4'
     02/18 11:10:45  transmission par.: '+FDCS:1,3,0,2,0,0,0,4'
     02/18 11:10:45  fax_wait_for: string 'CONNECT'** found **
     02/18 11:10:45  waiting for XON, got:[0a][11]
     02/18 11:10:45  sending f1.g3...
     02/18 11:11:03  sending DLE ETX...
     02/18 11:11:03  fax_wait_for(OK)
     02/18 11:11:16  fax_wait_for: string 'OK'** found **
     02/18 11:11:16  fax_command: send 'AT+FET=2'
     02/18 11:11:16  fax_wait_for(OK)
     02/18 11:11:16  fax_wait_for: string 'AT+FET=2'
     02/18 11:11:25  fax_wait_for: string '+FPTS:1'
     02/18 11:11:25  page status: +FPTS:1
     02/18 11:11:26  fax_wait_for: string '+FHNG:00'
     02/18 11:11:26  connection hangup: '+FHNG:00'
     02/18 11:11:26  (Normal and proper end of connection)
     02/18 11:11:26  fax_wait_for: string 'OK'** found **
     02/18 11:11:26  fax_send: 'AT+FCLASS=0^M'
     02/18 11:11:26  removing lock file


File: mgetty.info,  Node: ftp,  Next: get-uucp,  Prev: logfiles,  Up: Problems

5.5 How to get the mentioned software by FTP?
=============================================

Most of the software mentioned in this document should be available on
most major ftp sites. Nevertheless, I've got so many questions about the
software that I'll list some ftp sites here.

   Furthermore, I'll list some other software that may be interesting
if you plan to use `mgetty+sendfax' in different environments than I do.

   * `mgetty+sendfax'

     The starting point to find mgetty releases is:

     FTP: ftp://mgetty.greenie.net/pub/mgetty/

     HTTP: http://mgetty.greenie.net/

     There are some mirrors, but all the official mirror sites are not
     working anymore, so in doubt, you'll need to use google to find
     mgetty download sites.

   * `pbmplus'

     I found the pbmplus package (bitmap manipulation tools) at the
     following places (most other sites mirroring X11 should also have
     them):

     src.doc.ic.ak.uk:`/computing/graphics/pbmplus10dec91.tar.Z'

     wuarchive.wustl.edu:`/packages/X11R5/contrib-pub/pbmplus10dec91.tar.Z'

     ftp.germany.eu.net:`/X11/contrib/pbmplus10dec91.tar.Z'

     ftp.leo.org:`/pub/comp/os/unix/networking/mgetty/'

     The `pbmplus' package has been superceded by the `NetPBM' package
     which has some more conversion tools (but also some more bugs). It
     should be available on the same sites. You could also check:

     wuarchive.wstl.edu:`/graphics/graphics/packages/NetPBM'

     ftp.rahul.net:`/pub/davidsen/source'

     ftp.informatik.uni-oldenburg.de:`/???'

     The `pbmtodot' program mentioned in the "fax" chapter can be found,
     if nowhere else, in the `mgetty' directory on ftp.leo.org (see
     above).

   * `FAS'

     Some sites carrying the `fas' serial driver for SCO Unix, ISC, ...:

     ftp.fu-berlin.de:`/pub/unix/driver/fas/fas-2.11.tar.gz'

     ftp.germany.eu.net:`/pub/newsarchive/comp.sources.unix/volume27/fas-2.11.0/*'

     src.doc.ic.ac.uk:`/usenet/comp.sources.unix/volume27/fas-2.11.0/*'

     As far as I know, the current version is 2.12, but you should find
     2.12 at the same places as 2.11. I never upgraded, 2.11 works very
     fine for me :)

   * `GhostScript'

     The GNU GhostScript postscript interpreter can be found at all
     sites carrying GNU Software. The "main" GNU site is
     _prep.ai.mit.edu_.

     The new version 3.x isn't GNU software anymore, but uses a special
     license. You can find it in `/pub/ghost/aladdin' on
     _ftp.cs.wisc.edu_, and on various other mirror sites (e.g.
     ftp.leo.org).

   * `hp2pbm'

     GhostScript is huge and slow... if you don't need it for other
     purposes, you could use Chris Lewis' hp2pbm package, placed at

     mgetty.greenie.net as `hp2pbm*' (in the mgetty directory mentioned
     above).

     This package contains all you need to convert ASCII or LJ PCL4 ->
     PBM, G3, PS, X windows, Epson 24 pin. Coupled with mgetty's
     `g32pbm', it's all you need to send ASCII or HP LJ via FAX, and
     display/print FAXes on X, PS, LJ, Epson, or via PBM utilities

     It performs better than most of the equivalent PBMPLUS utilities.
     Indeed, if your application can generate both LJ and PS,
     generating LJ and converting to G3 via `hp2pbm' is *much* faster
     than generating PS and converting via GhostScript.

     [Citing Chris: Incidentally, "g32pbm" plus my "pbm2lj" is much
     faster than g3tolj.  Am not entirely sure why yet.  May have
     something to do with scaling, which g32pbm and pbm2lj don't do.]

   * `psroff'

     ftp.uunet.ca:`/distrib/chris_lewis/psroff3.0pl17/*'

     [Chris: It should be ...psroff/*, but they never answer when I ask
     them to fix my symlink]

     Contains all you need to generate PS, LJ, or ditroff from ditroff
     or CAT troff or groff. Together with hp2pbm, you can generate
     FAXes.  Contains quite a number of LJ fonts, font manipulation,
     and font scaling utilities.

     With the last two tools, you can send, receive, and print FAXes
     using _just_ mgetty and hp2pbm (and a Laserjet printer ;-),
     without needing pbmplus or GhostScript or anything else.

   * `Ifmail'

     Ifmail is Eugene Crosser's FidoNet (tm) compatible mailer + gateway
     software for Unix and Linux. Together with `mgetty', it provides
     the perfect modem solution, allowing incoming Fido calls as well
     as Unix-Login and fax. It can be found on:

     tsx-11.mit.edu:`/pub/linux/sources/usr.bin/ifmail*'

     sunsite.unc.edu:`/pub/Linux/system/Fido/ifmail*'

   * `dialog'

     Dialog is a very nice shell tool to simplify input/output
     functions in shell scripts. All the programs in
     `mgetty/frontends/dialog/' rely on it. It runs on most operating
     systems (except FreeBSD), as long as they have a `curses' library.
     The source can be found on

     sunsite.unc.edu:`/pub/Linux/utils/shell/dialog*'

   * `ps2g3'

     is a small package to integrate `mgetty+sendfax' into the NeXTStep
     operating system. It can be found on ftp.leo.org in the directory
     `/pub/comp/platforms/next/Tools/postscript/ps2g3.s.tar.gz'.

   * `dvips5.47'

     Dvips 5.x and up create a strange kind of postscript that, when
     converted with Ghostscript 3.x, produces Fax files that can not be
     faxed to paper fax machines (modems work fine) because the line
     width isn't exactly 1728 pixels. Dvips 5.47 doesn't do this. It
     can be found on:

     `ftp.leo.org:/pub/comp/os/unix/networking/mgetty/dvips*'

     `midway.uchicago.edu:pub/tex/dvips/dvips547.tar.Z'

   * `g3vga'

     Is a nice, fast G3 viewer for Linux and SVGALIB (standard console
     mode, no X11). You can find it in `.../apps/graphics/viewers' on
     all mirrors of SunSITE.unc.edu.



File: mgetty.info,  Node: get-uucp,  Prev: ftp,  Up: Problems

5.6 How to get the mentioned software by UUCP
=============================================

For those of you that do not have FTP access: all the software
mentioned in the last section can also be found on the following UUCP
sites:

   * GREENIE (my system): ++49-89-35663089, V32bis/V.34, get
     greenie!~/green.files.gz

   * CameloT (Frank Bartels): ++49-89-8948040, V34+, get /pub/ls-lR.gz



File: mgetty.info,  Node: Thanks,  Prev: Problems,  Up: Top

6 Thanks
********

Many thanks to (in no special order):

   * Peter Bechtold, peter@fns.greenie.muc.de, for sending me dozens of
     faxes to test mgetty, for calling me back numerous times after
     failed attempts to send him a fax with sendfax, ...

     Further, for the idea to use the remote fax id as part of the
     filename on received faxes.

   * Klaus Weidner, klaus@greenie.muc.de, for the original linux port,
     testing dozens of pre-releases, writing the original texinfo
     documentation, and finally for writing `vgetty'.

   * Lawrence 'dreamer' Chen, lawrence@combdyn.com, for the initial ISC
     port, and for testing the package with a SupraFAX-Modem.

   * Kay Schulz, kschulz@gold.t-informatik.ba-stuttgart.de, for testing
     on ISC -- and telling me that it's possible to ask dozens of
     questions without having ever read the README file ...

   * Georg Edelmann, georg@alpha.saar.de, for testing on Linux, and
     finding some stupid bugs.

   * Uwe S. Fuerst, uwe@phiger.com, for testing on SCO 3.2v4 (and
     helping me a lot nailing down the problem with dial-in/dial-out)

   * Bodo Bauer, bodo@hal.nbg.sub.org, for porting mgetty to SVR4
     (though he did quite confuse me by insisting that the fax receiver
     does not work ...), and later, bodo@suse.de, for his `faxrunqd'
     daemon.

   * Christoph Adomeit, for bugging me long enough to implement XON /
     XOFF flow control in fax sending / receiving, and for lending me
     one of his GVC modems long enough to make faxing (well, fax
     sending) work with it.

   * Christopher M. Ward, for testing on SCO with another GVC modem.

   * Ralf Stephan, for finding a problem in sendfax whith some modems
     that lower CD too soon.

   * John C. Peterson, for correcting a similar problem in mgetty /
     faxrec.

   * Chel van Gennip, for the `pbmscale', `g3toxwd' and `g3tolj'
     programs.

   * Glenn Thobe and Chris Lewis, for doing the 3B1 port(s).

   * Chris Lewis, for doing all the `/etc/gettdefs' stuff, CallerID,
     space limiting, making the source look really awful (K&R C
     support), miscellaneous minor fixes, and tolerating my sometimes
     very unfriendly reactions to his suggestions.

   * Caz Yokoyama, for his suggestions concerning faxspool and the
     mail-to-fax gateway

   * Martin Husemann, for SVR4 testing (damn ESIX) and the NetBSD 386
     port

   * Michael A. Meiszl, mam@mamunx.werries.de, because he asked me to
     (*grin*) - and because he found + changed lots of small,
     nevertheless annoying things.

   * Brent Mosbrook from ZyXEL USA, brentm@zyxel.com, who has been
     *very* helpful solving some ZyXEL-specific and generic fax
     questions.

   * ELSA Computer GmbH, Germany, for giving me a number of test modems
     and being pretty suportive overall concering questions of modem
     firmware, protocol handling, and so on.  A big thanks!

   * Sam Leffler, sam@sgi.com, for many interesting discussions and
     insights.

   * Christian Starkjohann, cs@ds1.kph.tuwien.ac.at, for important
     parts of the NeXT port.

   * Geoffrey Collyer and Henry Spencer, for writing the `newslock.c'
     program I use in `faxrunq'.

   * Simone "Neko" Demmel, for going to bed early, giving me time to
     proof read this manual and correct all the nasty bugs.

   * Russel Nelson, nelson@crynwr.com, for hosting the mgetty mailing
     list since December '96.

   * Medat Computer GmbH, Munich, for using mgetty+sendfax and paying
     me for improvements (faxrunqd rewrite and lots of detail work).

   * SpaceNet GmbH, Munich, for sponsoring IP connectivity for
     alpha.greenie.net.  Should you ever need an Internet Service
     Provider in Germany, look at http://www.space.net/...

   * Wiebke Baars, for being a really good friend, and for a number of
     wonderful days spent together.

   * ... and to all others who contributed in some way.




Tag Table:
Node: Top522
Node: Intro966
Node: Copying1791
Node: Overview2675
Node: Supported6001
Node: Install8928
Node: intro-runtime11575
Node: mgetty12399
Node: How13184
Node: Inittab17180
Node: Devices19635
Node: Logs21301
Node: Deny21921
Node: Direct23131
Node: Interaction24007
Node: Caller-ID26013
Node: runtime-mgetty30857
Node: Fax54181
Node: Convert55441
Node: Receiving60937
Node: Sending64296
Node: Polling67646
Node: Queuing68774
Node: Fax-Tools72041
Node: Scanner75826
Node: runtime-sendfax77038
Node: voice87621
Node: Problems89041
Node: Modems89635
Node: Common91286
Node: Zyxel104318
Node: TelelinkIMS08109075
Node: Rockwell110823
Node: Zoom-vfast112997
Node: Best14496EC113708
Node: GVC114181
Node: creatix114999
Node: Telekom115566
Node: Dallas116575
Node: Everex116848
Node: Exar117168
Node: Tornado117976
Node: Zoltrix118473
Node: MultiTech119194
Node: ELSA123054
Node: USR124898
Node: Elink-ISDN129542
Node: i4l131826
Node: i4l-capi134956
Node: Class 1137165
Node: Systems137852
Node: OS-Generic139766
Node: SCO-322140952
Node: SCO-324141978
Node: Linux144583
Node: ISC149863
Node: SVR4150845
Node: SVR42152015
Node: BSD153923
Node: AIX155235
Node: SunOS156780
Node: Solaris2158520
Node: 3b1160681
Node: HP-UX161749
Node: NEXTSTEP162163
Node: Darwin165636
Node: General167230
Node: pbmtog3167506
Node: Locks168662
Node: login-hang169566
Node: ecu171178
Node: logfiles171669
Node: log-mgetty-data172691
Node: log-mgetty-fax174413
Node: log-mgetty-syslog176154
Node: log-sendfax178999
Node: ftp182507
Node: get-uucp188342
Node: Thanks188806

End Tag Table
